參數資料
型號: M32000D3FP
元件分類: 微控制器/微處理器
英文描述: 32-BIT, 66.6 MHz, RISC MICROCONTROLLER, PQFP100
封裝: 14 X 20 MM, 0.65 MM PITCH, PLASTIC, LQFP-100
文件頁數: 4/155頁
文件大小: 1340K
代理商: M32000D3FP
M32000D3FP User's Manual
MASTER/SLAVE MODE
7-3
CLKIN
INT or SBI
INT or SBI input
RST
HREQ
HACK
CS
A8 - A30
BCH, BCL
SID, R/W
D0 - D15
DC
Hi-z
(see note 3)
Hi-z
program loading period before starting
(see note 1)
interrupt input for starting request
(see note 2)
reset period
(see note 3)
Notes 1: The external bus master (master M32000D3FP or external DMAC) downloads the program.
2: The slave M32000D3FP starts operation when an INT or SBI signal is input. Return the EI request
input to an "H" level after starting the slave M32000D3FP.
When starting the M32000D3FP in slave mode after reset or after returning from standby mode,
the interrupt request is always accepted when an "L" level signal of 1 CLKIN width is input to the
INT pin or SBI pin, because they are continously monitored.
3: The shaded area indicates the undefined state. "Hi-z" means high-impedance and
indicates
sampling timing.
7.2 Slave mode operation
7.2.1 Starting M32000D3FP in slave mode
When set to slave mode, the M32000D3FP does not execute instruction fetch operations to the reset vector
(address H'7FFF FFF0) even after a reset. Input the interrupt request to start execution of slave M32000D3FP
operations.
After a reset, the master M32000D3FP or an external DMAC downloads a program to the slave M32000D3FP
then, when an EI or SBI is input, the slave M32000D3FP starts operation. In this case, the IE bit in the
PSW register is "0", however, the first external interrupt (EI) to start the slave M32000D3FP is accepted.
The start address for each input is as follows.
EI: execute from address H'00000080
SBI: execute from address H'00000010
In either case, the EIT processing (hardware pre-processing and hardware post-processing) is executed.
Before executing the RTE instruction, set the return address in the BPC (to the top address of the program
to be executed) and the PSW register value to be used by the program to the BPSW filed in the PSW
register.
Fig. 7.2.1 Starting slave mode of M32000D3FP
相關PDF資料
PDF描述
M32171F2VFP 32-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP144
M32171F4VFP 32-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP144
M32176F4TFP 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP144
M32176F2TFP 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP144
M32180F8TFP 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP240
相關代理商/技術參數
參數描述
M32000D4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE CHIP 32 BIT CMOS MICROCOMPUTER
M32000D4AFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE CHIP 32 BIT CMOS MICROCOMPUTER
M32000D4BFP-80 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 32-BIT CMOS MICROCOMPUTER
M32002AGLJ 制造商:MTRONPTI 制造商全稱:MTRONPTI 功能描述:9x14 mm, 3.3/2.5/1.8 Volt, PECL/LVDS/CML, VCXO
M32002AGMJ 制造商:MTRONPTI 制造商全稱:MTRONPTI 功能描述:9x14 mm, 3.3/2.5/1.8 Volt, PECL/LVDS/CML, VCXO