參數資料
型號: TSB43AA82A1
廠商: Texas Instruments, Inc.
英文描述: 1394 integrated PHY and link layer controller(1394集成PHY和鏈路層控制器)
中文描述: 1394綜合物理層和鏈路層控制器(1394集成物理層和鏈路層控制器)
文件頁數: 99/146頁
文件大?。?/td> 597K
代理商: TSB43AA82A1
87
8.4.2.3 Write Requests With Specific Address (Direct Mode)
To receive a write request using the write request for block with specified address:
Set DRFEn (90h, bit 2) to 1.
Set DRPktz (90h, bit 4) to 0 to disable the packetizer mode.
Set DRFAdrEn (C0h, bit 2) to 1 to enable write request receiving.
When write requests for block packets are received to addresses specified with DRF destination offset hi/low and DRF
destination width, the packets are received by the DRF. The following formula shows a range of receivable packet
addresses:
DRF Destination Offset
Packet Address
DRF Destination Offset + DRF Destination Width
where: DRF Destination Offset specifies initiator’s BusID and NodeID.
Setting DRBIdEn (C0h, bit 0) to 1 can limit the initiator BusID, and setting DRSIdEn (C0h, bit 1) to 1 can limit the
initiator NodeID. DAckPnd (90h, bit 22) controls acknowledgements of the write request packet to the DRF. When
DAckPnd is 0, the response acknowledgement is complete. When DAckPnd is 1, the response acknowledgement
is pending. When a pending acknowledgement is sent and DRespComp (90h, bit 23) is 1, the response is complete.
8.4.2.4 Packetizer
To receive data by automatically creating an SBP-2 compliant read request for block packet:
Set DRFEn (90h, bit 2) to 1. Setting DRPktz (90h, bit 4) to 1 changes to packetizer mode.
Write expected block data information into DRF control registers 13 (C4h, C8h and CCh).
Write block data information in DRF control register 0 (C0h, bits 02), and simultaneously write 10 in
DRFCtl0DRFCtl1 to start packetizer operation.
A packetizer creates and transmits a block data read request based on the block data information.
Each time a packetizer receives an expected response packet, it makes a new request and repeats this
process. When packetizer operation stops due to completion of a transaction or some errors, DRFEnd
interrupt is created, and its result is displayed on DRFSt (C0h).
8.4.2.5 Specified as a Default
Setting 1 on RUEsel (08h, bit 25) makes DRF receive packets as a default. With this, the DRF receives read/write,
command fetch packets, and ARF to each agent, and all other unspecified packets.
8.4.3
Reading DRF Through the CFR
To read DRF data through the CFR:
Set DRDSel (90h,bit28) to 0. The microcontroller can get packets in their respective order by reading the
DRF data (ACh) register.
NOTE:
DRF data can be read through the CFR or the bulky interface (see Section 8.4.4). These
can be used individually or in combination.
相關PDF資料
PDF描述
TSB81BA3I IEEE 1394b THREE-PORT CABLE TRANSCEIVER/ARBITER
TSE-0155-32S-P1-3 SINGLE MODE SINGLE FIBER TRANSCEIVER
TSL230 PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS
TSL235(中文) Programmable Light-To-Frequency Converter(光頻轉換器)
TSL245(中文) IR Light-To-Frequency Converter(紅外光頻轉換器)
相關代理商/技術參數
參數描述
TSB43AA82AI 制造商:TI 制造商全稱:Texas Instruments 功能描述:1394 Integrated PHY and Link-Layer Controller for SBP-2 Products and DPP Products
TSB43AA82AIPGE 功能描述:1394 接口集成電路 Hi Perf Integr Phy & Link Layer Chip RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray
TSB43AA82AIPGEEP 功能描述:1394 接口集成電路 Mil Enh Int PHY and Link-Layer Cntrlr RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray
TSB43AA82APGE 功能描述:1394 接口集成電路 Hi Perf Integr Phy & Link Layer Chip RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray
TSB43AA82APGEG4 功能描述:1394 接口集成電路 Hi Perf Integr Phy & Link Layer Chip RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray