- 您現在的位置：買賣IC網 > PDF目錄385949 > TSB43AA82A1 (Texas Instruments, Inc.) 1394 integrated PHY and link layer controller(1394集成PHY和鏈路層控制器) PDF資料下載
參數資料
| 型號： | TSB43AA82A1 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 1394 integrated PHY and link layer controller(1394集成PHY和鏈路層控制器) |
| 中文描述： | 1394綜合物理層和鏈路層控制器（1394集成物理層和鏈路層控制器） |
| 文件頁數： | 56/146頁 |
| 文件大?。?/td> | 597K |
| 代理商： | TSB43AA82A1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁
330
3.4.39.4 DRF Control Register 3 at CCh
BITS
ACRONYM
DIR
DESCRIPTION
031
DRF_destination_offset_lo
R/W
DRF receive destination start offset low. DRF_destination_offset_lo specifies the transferred
destination offset low.
3.4.40 DRF Control Registers at C0h, C4h, C8h, and CCh (DRPktz at 90h = 1)—Packetizer
When DRPktz is set to 1, the DRF control registers describe the packetizer mode. The packetizer mode is primarily
used with SBP-2. These registers default to 0000 0000h and, except for the bits specified, are unaffected by a bus
reset.
3.4.40.1 DRF Control Register 0 at C0h
BITS
ACRONYM
DIR
DESCRIPTION
01
DRFCTL[0:1]
R/W
DRF packetizer transmit control. Table 33 describes the read and write values of these control bits.
2
DRFClr/DRFst
R/W
DRF clear control bit (write) / DRF status transmit (read)
When DRFClr is set to 1, the DRF data is cleared. This bit is automatically set to 0 when the DRF is cleared.
DRFClr must not be asserted when DRFCtl is busy. When DRFst is set to 0, the read value specifies the
current transaction status.
3
DRFNdIdval
R/O
DRF NodeID valid. This bit represents a valid NodeID in DRF destination ID. This bit is 1 when the
destination ID at C8h is changed. This bit defaults to 0 and is set to 0 on a bus reset.
4
DRFNotify
R/W
DRF notify. When this bit is set to 1, transaction status data is transferred following a DRF data transfer.
5
Reserved
N/A
Reserved
67
DRFSpd
R/W
DRF transaction speed. DRFSpd specifies the speed used by the DRF packetizer.
00 : 100 Mbps
01 : 200 Mbps
10 : 400 Mbps
11 : Not valid
811
DRF Max Payload
R/W
DRF transfer maximum payload. DRFMaxPayload is used to calculate the maximum data transfer length
that the DRF packetizer requests in a single read transaction. The maximum data transfer length is
specified as 2(DRFMaxPayload + 2) .
12
PgTblEn
R/W
Page table enable. PgTblEn controls page table fetching. When PgTblEn is set to 1, page table fetching is
enabled. DRF_destination_offset_hi and DRF_destination_offset_lo data point to the page table address.
When PgTblEn is 0 and AutoPg is set to 1, page table fetching is disabled. DRF_destination_offset_hi and
DRF_destination_offset_lo are data areas.
1315
DRF Page Size
R/W
DRF receive page size. DRF Page Size specifies the underlying page size of data buffer memory. Any one
request packet is not permitted to cross a page boundary. DRF Page Size value of zero indicates that the
underlying page size is not specified. Otherwise, the page size is 2(DRFPageSize + 8).
1631
DRF_BlockSize/
DRF_BlockCount
R/W
DRF transmit block size / DRF transmit block count. When LngBlk in DMA control (90h) is set to 0, this
value is the DRF_BlockSize. DRF_BlockSize specifies the transmitted blocksize value in bytes. When
LngBlk is set to 1, the value is the DRF_BlockCount. DRF_BlockCount specifies the number of transmitted
blocks. DRF_BlockCount is decremented during transmission automatically.
Table 33. DRFCtl: DRF Packetizer Transmit Control
READ VALUE
WRITE VALUE
DRFCTL0
DRFCTL1
STATE
DRFCTL0
DRFCTL1
STATE
0
0
IDLE
0
0
No operation
1
0
BUSY
1
0
Start/restart
1
1
PEND
1
1
Init-start
0
1
PAGEFAULT
0
1
Abort
相關PDF資料 |
PDF描述 |
|---|---|
| TSB81BA3I | IEEE 1394b THREE-PORT CABLE TRANSCEIVER/ARBITER |
| TSE-0155-32S-P1-3 | SINGLE MODE SINGLE FIBER TRANSCEIVER |
| TSL230 | PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS |
| TSL235(中文) | Programmable Light-To-Frequency Converter(光頻轉換器) |
| TSL245(中文) | IR Light-To-Frequency Converter(紅外光頻轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSB43AA82AI | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1394 Integrated PHY and Link-Layer Controller for SBP-2 Products and DPP Products |
| TSB43AA82AIPGE | 功能描述:1394 接口集成電路 Hi Perf Integr Phy & Link Layer Chip RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB43AA82AIPGEEP | 功能描述:1394 接口集成電路 Mil Enh Int PHY and Link-Layer Cntrlr RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB43AA82APGE | 功能描述:1394 接口集成電路 Hi Perf Integr Phy & Link Layer Chip RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB43AA82APGEG4 | 功能描述:1394 接口集成電路 Hi Perf Integr Phy & Link Layer Chip RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。