- 您現在的位置：買賣IC網 > PDF目錄385949 > TSB43AA82A1 (Texas Instruments, Inc.) 1394 integrated PHY and link layer controller(1394集成PHY和鏈路層控制器) PDF資料下載
參數資料
| 型號： | TSB43AA82A1 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 1394 integrated PHY and link layer controller(1394集成PHY和鏈路層控制器) |
| 中文描述： | 1394綜合物理層和鏈路層控制器（1394集成物理層和鏈路層控制器） |
| 文件頁數： | 96/146頁 |
| 文件大小： | 597K |
| 代理商： | TSB43AA82A1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁當前第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁
84
Table 83. Status-Block Format Descriptions
FIELD NAME
AsAgent
DESCRIPTION
Associates corresponding agent for this transaction. The difference between associated and nonassociated is
whether the status transfer is successful or not successful. The agent status specified by agent number falls into a
dead state. Setting AsAgent to 0 activates the AsAgent and changes agentnum.
Specifies the agent number associated by this transaction.
The concatenation of these two fields addresses a quadlet in the destination node address space. This address must
be quadlet aligned (modulo 4) and the address of the status FIFO at the initiator.
data_length is the number of bytes of status block size transmitted in the packet.
The block extended_tCode to be performed on the data in this packet. See Table 6-11 of the IEEE 1394-1995
standard.
SBP-2 status block. Refer to the SBP-2 standard for more information.
agentnum
destination_offset_high,
destination_offset_low
data_length
extended_tCode
status Block
To load status block packet into internal RAM:
1.
Set the size of status block FIFO in the MTXBufSiz bit (94h). For example, to set 8 quadlets of the entire
status block packet, write 06h to this field. This field should be half the size of the status block packet in
quadlets.
2.
Set internal RAM to write status mode. DTFST/DRFST bits (F8h) enable access to the status FIFO. Once
one of the bits is set to 1, the host can access the status FIFO.
3.
Write the status block packet. The host can write the status block packet through the log data register (FCh).
Address requests written to FCh are processed automatically.
4.
Activate the status block. Set the notify bit enable to send the status block packet. Notify bits are located
at DTF and DRF control registers.
8.4
DMA Operation
8.4.1
Packet Transmission by DTF
There are three modes of packet transmission with DTF:
Writing to the CFR through the microcontroller
Through the bulky interface in direct mode (DTPktz at 90h = 0)
Through the bulky interface in packetizer mode (DTPktz at 90h = 1)
8.4.1.1 Packet Transmission by Writing to the CFR Through the Microcontroller
By clearing the DTDSel bit (90h, bit 29), the host can write a packet to DTF using DTF_First&Continue (A4h) and
DTF_update (A8h). In this case, the DMA bulky interface can not write data to the DTF.
Set DTFEn (90h, bit 3) to 1 and DTPktz (90h, bit 5) to 0 to enable DTF transmission through the
microcontroller.
Set DTHdIs (90h, bit 24) to 0 to disable header insertion.
Set DTDSel (90h, bit 29) to 0 to switch to CFR packet write mode.
Write a packet excluding the last quadlet into DTF first and continue register (A4h). This complies with the
DTF format defined in Section 8.2.2.
Start the transmission request by writing the last quadlet to the DTF update register (A8h).
At the completion of a packet transmission, DTAVal is set and an appropriate acknowledgement is displayed
on DTxAck (A0h).
When DTSpDis (90h, bit 7) is 1, or no split transaction has occurred, a DTFEnd interrupt is created to end
the transmission transaction.
When DTSpDis (90h, bit 7) is 0 and split transaction(s) has occurred, a DTFEnd interrupt is created to end
the transmission transaction after a response packet is received.
In this case, a response packet is received by DRF.
相關PDF資料 |
PDF描述 |
|---|---|
| TSB81BA3I | IEEE 1394b THREE-PORT CABLE TRANSCEIVER/ARBITER |
| TSE-0155-32S-P1-3 | SINGLE MODE SINGLE FIBER TRANSCEIVER |
| TSL230 | PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS |
| TSL235(中文) | Programmable Light-To-Frequency Converter(光頻轉換器) |
| TSL245(中文) | IR Light-To-Frequency Converter(紅外光頻轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSB43AA82AI | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1394 Integrated PHY and Link-Layer Controller for SBP-2 Products and DPP Products |
| TSB43AA82AIPGE | 功能描述:1394 接口集成電路 Hi Perf Integr Phy & Link Layer Chip RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB43AA82AIPGEEP | 功能描述:1394 接口集成電路 Mil Enh Int PHY and Link-Layer Cntrlr RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB43AA82APGE | 功能描述:1394 接口集成電路 Hi Perf Integr Phy & Link Layer Chip RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB43AA82APGEG4 | 功能描述:1394 接口集成電路 Hi Perf Integr Phy & Link Layer Chip RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。