
Revision History
8
December 2003 Revised March 2005
SPRS231D
PAGE(S)
NO.
ADDITIONS/CHANGES/DELETIONS
188
Updated Section 4.1, Device and Development-Support Tool Nomenclature
189
Added Figure 41, Example Markings for OMAP5912 ZDY Package
190
Updated Section 5.1, Absolute Maximum Ratings
191
Updated Section 5.2, Recommended Operating Conditions [Revision C] and
[Revision D]
193
Section 5.3, Electrical Characteristics Over Recommended Operating
Case
Temperature Range (Unless Otherwise Noted):
V
OH
(High-level output voltage), Standard LVCMOS:
changed TEST CONDITIONS
V
OL
(Low-level output voltage), Standard LVCMOS:
changed TEST CONDITIONS
V
OL
(Low-level output voltage), I
2
C:
changed TEST CONDITIONS from “Fast mode at
6
-mA load” to “Fast mode at 2-mA load” and changed
its MAX value from 0.6 V to 0.4 V
Fast mode at 3-mA load: changed MAX value from 0.4 V to 0.6 V
changed TEST CONDITIONS from “Standard mode at
3
-mA load” to “Standard mode at 2-mA load”
I
I
(Input current), Input pins with
20
-
μ
A
pulldowns enabled
, Low-voltage range:
changed MAX value from 20
μ
A to 25
μ
A
I
I
(Input current), Input pins with
20
-
μ
A
pulldowns enabled
, High-voltage range:
changed MAX value from 60
μ
A to 95
μ
A
I
I
(Input current), Input pins with
100
-
μ
A
pulldowns enabled
, Low-voltage range:
changed MAX value from 170
μ
A to 185
μ
A
I
I
(Input current), Input pins with
100
-
μ
A
pulldowns enabled
, High-voltage range:
changed MAX value from 110
μ
A to 185
μ
A
I
I
(Input current), Input pins with
20
-
μ
A
pullups enabled
, Low-voltage range:
changed MIN value from 20
μ
A to 25
μ
A
I
I
(Input current), Input pins with
20
-
μ
A
pullups enabled
, High-voltage range:
changed MIN value from 60
μ
A to 95
μ
A
I
I
(Input current), Input pins with
100
-
μ
A
pullups enabled
, Low-voltage range:
changed MIN value from 170
μ
A to 185
μ
A
I
I
(Input current), Input pins with
100
-
μ
A
pullups enabled
, High-voltage range:
changed MIN value from 110
μ
A to 185
μ
A
194
Updated Figure 51, 3.3-V Test Load Circuit
“Package Thermal Resistance Characteristics” section (was Section 5.4) has been moved to Section 7.1
196
Table 52, 32-kHz Input Clock Timing Requirements:
CK1: changed symbol from “t
cyc
” to “1/t
cyc
”
CK5, Frequency stability:
changed MIN value from 70 ppm to 250 ppm
changed MAX value from 70 ppm to 250 ppm
added footnote about frequency stability requirement
197
Section 5.5.2, Base Oscillator (12, 13, or 19.2 MHz) and Input Clock:
changed first sentence of second paragraph
from
“... with a maximum effective series resistance of
30
“... with a maximum effective series resistance of
50
added Table 54, 12-MHz to 19.2-MHz Input Clock Timing Requirements
added Figure 56, Input Clock Timings
maximum
.”
to
maximum and a power dissipation of 0.5 mW
.”