參數資料
型號: DS3112N
廠商: DALLAS SEMICONDUCTOR
元件分類: Digital Transmission Controller
英文描述: DATACOM, FRAMER, PBGA256
封裝: 27 X 27 MM, PLASTIC, BGA-256
文件頁數: 60/134頁
文件大?。?/td> 900K
代理商: DS3112N
DS3112
31 of 134
SECTION 4: MASTER DEVICE CONFIGURATION AND STATUS/INTERRUPT
4.1 MASTER RESET AND ID REGISTER DESCRIPTION
The Master Reset and ID (MRID) register can be used to globally reset the device. When the RST bit is
set to one, all of the internal registers will be placed into their default state which is 0000h. A reset can
also be invoked by the RST* hardware signal.
The upper byte of the MRID register is read only and it can be read by the Host to determine the chip
revision. Contact the factory for specifics on the meaning of the value read from the ID0 to ID7 bits.
Register Name:
MRID
Register Description:
Master Reset and ID Register
Register Address:
00h
Bit #
7
6
5
4
3
2
1
0
Name
n/a
T3E3RSY T2E2RSY
RFIFOR
RST
Default
-
0
Bit #
15
141312
1110
9
8
Name
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
Default
1
010
000
1
Note: Bits that are underlined are read only; all other bits are read-write.
Bit 0 / Master Software Reset (RST). When this bit is set to a one by the Host, it will force all of the
internal registers to their default state which is 0000h and forces the T3/E3 and T1/E1 outputs to send an
all ones pattern. This bit must be set high for a minimum of 100ns. This software bit is logically OR’ed
with the hardware signal RST*.
0 = normal operation
1 = force all internal registers to their default value of 0000h
Bit 1 / Low Speed (T1/E1) Receive FIFO Reset (RFIFOR). A 0 to 1 transition on this bit will cause
the receive T1/E1 demux FIFOs to be reset which will causes them to be flushed. See the DS3112 Block
Diagrams in Figures 1A and 1B for details on the placement of the FIFOs within the chip. This bit must
be cleared and set again for a subsequent reset to occur.
Bit 2 / T2/E2/G747 Force Receive Framer Resynchronization (T2E2RSY). A 0 to 1 transition on this
bit will cause all seven of the T2 receive framers or all four of the E2 receive framers or all seven of the
G747 framers to resynchronize. This bit must be cleared and set again for a subsequent resynchronization
to occur.
相關PDF資料
PDF描述
DS3112 DATACOM, FRAMER, PBGA256
DS3131 SPECIALTY TELECOM CIRCUIT, PBGA256
DS3134 DATACOM, FRAMER, PBGA256
DS3150QN DATACOM, PCM TRANSCEIVER, PQCC28
DS3150Q DATACOM, PCM TRANSCEIVER, PQCC28
相關代理商/技術參數
參數描述
DS3112N+ 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112N+W 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112NC1 制造商:Maxim Integrated Products 功能描述:T3 E3 MULTIPLEXER, 3.3V T3/E3 FRAMER AND M13/E13/G.747 MUX - Rail/Tube
DS3112ND1E 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
DS3112RD 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray