- 您現在的位置：買賣IC網 > PDF目錄359147 > MC72000 (飛思卡爾半導體(中國)有限公司) Integrated Bluetooth Radio PDF資料下載
參數資料
| 型號： | MC72000 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Integrated Bluetooth Radio |
| 中文描述： | 集成藍牙無線 |
| 文件頁數： | 32/156頁 |
| 文件大?。?/td> | 1782K |
| 代理商： | MC72000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁
32
MC72000 Advance Information Data Sheet
Go to: www.freescale.com
MOTOROLA
Radio Functional Description
6.1 RF Receive Chain
The MC72000 is placed into the receive mode from the idle mode by asserting the internal RXTXEN
master signal after setting the Radio Receive Enable bit (R2/13), clearing the Radio Transmit Enable bit
(R2/14), and clearing the Radio Narrow Bandwidth Enable bit (R2/12). The data represents a 6-Bit,
2’s-complement digital value and is sampled four times for every data bit. Once the receive cycle is
complete, the RXTXEN master signal to the radio is deasserted and the MC72000 begins an internal power
down sequence. This is all controlled by the internal baseband processor. The receive chain is optimized to
provide high adjacent channel rejection, which is the most important specification in a high interference
environment. This is accomplished by setting the IF bandpass filter to 720 kHz and then using Maximum
Likelihood Sequence Estimation (MLSE) in baseband processing to remove the effects of intersymbol
interference.
A low voltage SPI interface is used between the radio and the baseband processor. The baseband
synchronizes the radio timing through the master RXTXEN signal to the radio. A logic low transition on
this signal indicates the beginning of idle state, while a logic high transition indicates either transmit or a
receive cycle.
6.2 RF Transmit Chain
The MC72000 is placed into the transmit mode from the idle mode by setting the Radio Transmit Enable
bit (R2/14), setting the Radio Narrow Bandwidth Enable bit (R2/12), and clearing the Radio Receive
Enable bit (R2/13) of the Radio Register Map, then asserting the RTXEN pin of the device. Once the data
stream has been transmitted, the RTXEN pin is deasserted and the MC72000 begins an internal power
down sequence. Since RF power is still present at the PA output, no SPI operations or additional cycles
between the radio and the baseband processor can be performed until a certain amount of time has passed
after the deassertion of RXTXEN. At this time, RF power is at a substantially low enough level so as not to
produce undesired emissions. The internal baseband processor also handles this timing.
6.3 Receiver
The MC72000 receiver is intended to be used in Time Division Duplex (TDD), Frequency Hopping
Spread Spectrum (FHSS) Bluetooth applications. The receiver uses a low intermediate frequency (IF) of
6.0 MHz and is capable of receiving up to 1.0 Mbit/s Gaussian Frequency Shift Keyed (GFSK) serial data
through the entire 2.4 GHz Industrial, Scientific, and Medical (ISM) band. The output of the receiver is a
demodulated, serial bit stream of 24 Mbit/s data. This data represents a 4X over sample by a 6-bit D/A of
the actual demodulated analog data recovered from the desired channel. A detailed discussion of each of
the functional blocks within the receiver is provided in the following sections.
6.3.1 LNA
The first portion of the receiver chain is the Low Noise Amplifier (LNA). The LNA is a bipolar cascode
design and provides gain with low noise at RF frequencies. The LNA is designed with a single-ended
(unbalanced) input and is converted to a differential (balanced) output by means of an on-chip, integrated
balun.
For optimum performance, the LNA input impedance must be matched to the complex conjugate of the
source impedance (usually 50
).
The LNA of the MC72000 exhibits two distinctly different impedances depending upon whether the LNA
is active or disabled. During a receive cycle, the S11 of the LNA is shown in the Table 16.
F
For More Information On This Product,
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC7445ARX1000LF | RISC Microprocessor Hardware Specifications |
| MC7445ARX1000LG | RISC Microprocessor Hardware Specifications |
| MC7447A | PowerPC microprocessor |
| MC7447AHX1000NB | PowerPC microprocessor |
| MC7447AHX1167NB | PowerPC microprocessor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC7220C-100M RI-BLK | 制造商:Farnell / Pro-Power 功能描述:CABLE DEF 7-2-20C 20CORE 100M 制造商:pro-power 功能描述:CABLE, DEF 7-2-20C, 20CORE, 100M 制造商:pro-power 功能描述:CABLE, DEF 7-2-20C, 20CORE, 100M; Reel Length (Imperial):328ft; Reel Length (Metric):100m; No. of Conductors:20; Voltage Rating:440V; No. of Strands x Strand Size:7 x 0.2mm; Conductor Area CSA:0.22mm2; Jacket Colour:Black; Jacket ;RoHS Compliant: Yes |
| MC7220C-100M RI-BLK | 制造商:Farnell / Pro-Power 功能描述:CABLE DEF 7-2-20C 20 CORE 100M |
| MC7220C-25M RI-BLK | 制造商:Farnell / Pro-Power 功能描述:CABLE DEF 7-2-20C 20CORE 25M 制造商:pro-power 功能描述:CABLE, DEF 7-2-20C, 20CORE, 25M |
| MC7220C-25M RI-BLK | 制造商:Farnell / Pro-Power 功能描述:CABLE DEF 7-2-20C 20 CORE 25M |
| MC7225C-25M RI-BLK | 制造商:Farnell / Pro-Power 功能描述:CABLE DEF 7-2-25C 25CORE 25M 制造商:pro-power 功能描述:MULTICORE, 25, 7/0.2MM, 25M, BLACK 制造商:pro-power 功能描述:CABLE, DEF 7-2-25C, 25CORE, 25M 制造商:PRIVATE LABEL 功能描述:CABLE, DEF 7-2-25C, 25CORE, 25M, Reel Length (Imperial):82ft, Reel Length (Metri |
發布緊急采購，3分鐘左右您將得到回復。