參數資料
型號： 38D5
廠商： Renesas Technology Corp.
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 75/141頁
文件大?。?/td> 2027K
代理商： 38D5
Rev.3.01
REJ03B0158-0301
Aug 08, 2007
Page 75 of 134
38D5 Group
Outline Performance
CPU rewrite mode is usable in the single-chip or Boot mode. The
only User ROM area can be rewritten.
In CPU rewrite mode, the CPU erases, programs and reads the
internal flash memory as instructed by software commands. This
rewrite control program must be transferred to internal RAM
area before it can be executed.
The MCU enters CPU rewrite mode by setting “1” to the CPU
rewrite mode select bit (bit 1 of address 0FE0
16
). Then, software
commands can be accepted.
Use software commands to control program and erase
operations. Whether a program or erase operation has terminated
normally or in error can be verified by reading the status register.
Figure 71 shows the flash memory control register 0.
Bit 0 of the flash memory control register 0 is the RY/BY status
flag used exclusively to read the operating status of the flash
memory. During programming and erase operations, it is “0”
(busy). Otherwise, it is “1” (ready).
Bit 1 of the flash memory control register 0 is the CPU rewrite
mode select bit. When this bit is set to “1”, the MCU enters CPU
rewrite mode. And then, software commands can be accepted. In
CPU rewrite mode, the CPU becomes unable to access the
internal flash memory directly. Therefore, use the control
program in the internal RAM for write to bit 1. To set this bit 1 to
“1”, it is necessary to write “0” and then write “1” in succession
to bit 1. The bit can be set to “0” by only writing “0”.
Bit 2 of the flash memory control register 0 is the user block 1
E/W enable bit. By setting combination of bit 4 (user block 0
E/W enable bit) of the flash memory control register 2 (address
0FE2
16
) and this bit as shown in Table 17, E/W is disabled to
user block in the CPU rewriting mode.
Bit 3 of the flash memory control register 0 is the flash memory
reset bit used to reset the control circuit of internal flash memory.
This bit is used when flash memory access has failed. When the
CPU rewrite mode select bit is “1”, setting “1” for this bit resets
the control circuit. To release the reset, it is necessary to set this
bit to “0”.
Bit 5 of the flash memory control register 0 is the User ROM
area select bit and is valid only in the boot mode. Setting this bit
to “1” in the boot mode switches an accessible area from the boot
ROM area to the user ROM area. To use the CPU rewrite mode
in the boot mode, set this bit to “1”. To rewrite bit 5, execute the
user original reprogramming control software transferred to the
internal RAM in advance.
Bit 6 of the flash memory control register 0 is the program status
flag. This bit is set to “1” when writing to flash memory is failed.
When program error occurs, the block cannot be used.
Bit 7 of the flash memory control register 0 is the erase status
flag.
This bit is set to “1” when erasing flash memory is failed. When
erase error occurs, the block cannot be used.
Figure 72 shows the flash memory control register 1.
Bit 0 of the flash memory control register 1 is the Erase suspend
enable bit. By setting this bit to “1”, the erase suspend mode to
suspend erase processing temporary when block erase command
is executed can be used. In order to set this bit 0 to “1”, writing
“0” and “1” in succession to bit 0. In order to set this bit to “0”,
write “0” only to bit 0.
Bit 1 of the flash memory control register 1 is the erase suspend
request bit. By setting this bit to “1” when erase suspend enable
bit is “1”, the erase processing is suspended.
Bit 6 of the flash memory control register 1 is the erase suspend
flag. This bit is cleared to “0” at the flash erasing.
Fig 71. Structure of flash memory control register 0
Fig 72. Structure of flash memory control register 1
Flash memory control register 0
(FMCR0: address : 0FE0
16
, initial value: 01
16
)
RY/BY status flag
0 : Busy (being written or erased)
1 : Ready
CPU rewrite mode select bit
(1)
0 : CPU rewrite mode invalid
1 : CPU rewrite mode valid
User block 1 E/W enable bit
(1, 2)
0 : E/W disabled (1800
16
-7FFF
16
)
1 : E/W enabled (1800
16
-7FFF
16
)
Flash memory reset bit
(3, 4)
0 : Normal operation
1 : reset
Not used (do not write “1” to this bit.)
User ROM area select bit
(5)
0 : Boot ROM area is accessed
1 : User ROM area is accessed
Program status flag
0: Pass
1: Error
Erase status flag
0: Pass
1: Error
b7
b0
Notes 1: For this bit to be set to “1”, the user needs to write a “0” and then a
“1” to it in succession. For this bit to be set to “0”, write “0” only to
this
bit.
2: This bit can be written only when CPU rewrite mode select bit is “1”.
3: Effective only when the CPU rewrite mode select bit = “1”. Fix this
bit to “0” when the CPU rewrite mode select bit is “0”.
4: When setting this bit to “1” (when the control circuit of flash memory
is reset), the flash memory cannot be accessed for 10
μ
s.
5: Write to this bit in program on RAM
Flash memory control register 1
(FMCR1: address: 0FE1
16
, initial value: 40
16
)
Erase Suspend enable bit
0 : Suspend invalid
1 : Suspend valid
(1)
Erase Suspend request bit
0 : Erase restart
1 : Suspend request
(2)
Not used (do not write “1” to this bit.)
Erase Suspend flag
0 : Erase active
1 : Erase inactive (Erase Suspend mode)
Not used (do not write “1” to this bit.)
b7
b0
Notes 1: For this bit to be set to “1”, the user needs to write a “0” and then a
“1” to it in succession. For this bit to be set to “0”, write “0” only to
this
bit.
2: Effective only when the suspend enable bit = “1”.
相關PDF資料
PDF描述
38F1222 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit
TA5M STECKER DIN MINI 5POL
70B5031 KUPPLUNG DIN MINI 5POL
39-26-3050 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit
390KD05JX 11 to 460 Volts Varistor 0.7 to 29 Joule
相關代理商/技術參數
參數描述
38D5_07 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Standard Characteristics Example
38D5_08 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
38D511G015FE6AD 制造商:Sprague/Vishay 功能描述:AL015X751
38D5-FMV 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Standard Characteristics (Flash Memory Version)
38DDP11B11M1QT 功能描述:SWITCH PUSH DPDT,O-N-O,N,SL,LF , 制造商:grayhill inc. 系列:* 零件狀態:在售 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*