- 您現在的位置：買賣IC網 > PDF目錄385274 > DS33ZH11 (MAXIM INTEGRATED PRODUCTS INC) Ethernet Mapper PDF資料下載
參數資料
| 型號： | DS33ZH11 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 網絡接口 |
| 英文描述： | Ethernet Mapper |
| 中文描述： | DATACOM, NETWORK INTERFACE SUPPORT CIRCUIT, PBGA100 |
| 封裝： | 10 X 10 MM, 1.41 MM HEIGHT, 0.80 MM PITCH, CSBGA-100 |
| 文件頁數： | 53/169頁 |
| 文件大小： | 1049K |
| 代理商： | DS33ZH11 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁
DS33Z11 Ethernet Mapper
8.15.4.1 Error Insertion
53 of 169
Error insertion inserts errors into the outgoing pattern data stream. Errors are inserted one at a time Single bit
error insertion can be initiated from the microprocessor interface. If pattern inversion is enabled, the data stream is
inverted before the overhead/stuff bits are inserted. Pattern inversion is programmable (on or off).
8.15.4.2 Performance Monitoring Update
All counters stop counting at their maximum count. A counter register is updated by asserting (low to high
transition) the performance monitoring update signal (PMU). During the counter register update process, the
performance monitoring status signal (PMS) is de-asserted. The counter register update process consists of
loading the counter register with the current count, resetting the counter, forcing the zero count status indication
low for one clock cycle, and then asserting PMS. No events shall be missed during an update procedure.
8.16 Transmit Packet Processor
The Transmit Packet Processor accepts data from the Transmit FIFO, performs bit reordering, FCS processing,
packet error insertion, stuffing, packet abort sequence insertion, inter-frame padding, and packet scrambling. The
data output from the Transmit Packet Processor to the Transmit Serial Interface is a serial data stream (bit
synchronous mode). HDLC processing can be disabled (clear channel enable). Disabling HDLC processing
disables FCS processing, packet error insertion, stuffing, packet abort sequence insertion, and inter-frame
padding. Only bit reordering and packet scrambling are not disabled.
Bit reordering changes the bit order of each byte. If bit reordering is disabled, the outgoing 8-bit data stream
DT[1:8] with DT[1] being the MSB and DT[8] being the LSB is output from the Transmit FIFO with the MSB in
TFD[7] (or 15, 23, or 31) and the LSB in TFD[0] (or 8, 16, or 24) of the transmit FIFO data TFD[7:0] 15:8, 23:16, or
31:24). If bit reordering is enabled, the outgoing 8-bit data stream DT[1:8] is output from the Transmit FIFO with
the MSB in TFD[0] and the LSB in TFD[7] of the transmit FIFO data TFD[7:0]. In bit synchronous mode, DT [1] is
the first bit transmitted. Bit Reordering can be controlled by address pin A0 in Hardware Mode.
FCS processing calculates an FCS and appends it to the packet. FCS calculation is a CRC-16 or CRC-32
calculation over the entire packet. The polynomial used for FCS-16 is x
+ x
+ x
+ 1. The polynomial used for
FCS-32 is x
+ x
+ x
+ x
+ x
+ x
+ x
+ x
+ x
+ x
+ x
+ x
4
+ x
2
+ x + 1. The FCS is inverted after
calculation. The FCS type is programmable. If FCS append is enabled, the calculated FCS is appended to the
packet. If FCS append is disabled, the packet is transmitted without an FCS. The FCS append mode is
programmable. If packet processing is disabled, FCS processing is not performed.
Packet error insertion inserts errors into the FCS bytes. A single FCS bit is corrupted in each errored packet. The
FCS bit corrupted is changed from errored packet to errored packet. Error insertion can be controlled by a register
or by the manual error insertion input (LI.TMEI.TMEI). The error insertion initiation type (register or input) is
programmable. If a register controls error insertion, the number and frequency of the errors are programmable. If
FCS append is disabled, packet error insertion will not be performed. If packet processing is disabled, packet error
insertion is not performed.
Stuffing inserts control data into the packet to prevent packet data from mimicking flags. A packet start indication
is received, and stuffing is performed until, a packet end indication is received. Bit stuffing consists of inserting a
'0' directly following any five contiguous '1's. If packet processing is disabled, stuffing is not performed.
There is at least one flag plus a programmable number of additional flags between packets. The inter-frame fill
can be flags or all '1's followed by a start flag. If the inter-frame fill is all '1's, the number of '1's between the end
and start flags does not need to be an integer number of bytes, however, there must be at least 15 consecutive
'1's between the end and start flags. The inter-frame padding type is programmable. If packet processing is
disabled, inter-frame padding is not performed.
Packet abort insertion inserts a packet abort sequences as necessary. If a packet abort indication is detected, a
packet abort sequence is inserted and inter-frame padding is done until a packet start flag is detected. The abort
sequence is FFh. If packet processing is disabled, packet abort insertion is not performed.
The packet scrambler is a x
43
+ 1 scrambler that scrambles the entire packet data stream. The packet scrambler
runs continuously, and is never reset. In bit synchronous mode, scrambling is performed one bit at a time. In byte
相關PDF資料 |
PDF描述 |
|---|---|
| DS3803 | 1024K Flexible NV SRAM SIMM(1024K靈活的非易失性SRAM SIMM) |
| DS3903E-020 | Triple 128-Position Nonvolatile Digital Potentiometer |
| DS3994 | 4-Channel Cold-Cathode Fluorescent Lamp Controller |
| DS4077 | 77.76MHz VCXO |
| DS4077L-0C0 | 77.76MHz VCXO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS33ZH11+ | 功能描述:網絡控制器與處理器 IC 10/100 ENETXPORT HMODE MAP IND RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS34 | 制造商:LUMILEDS 制造商全稱:LUMILEDS 功能描述:power light source Luxeon V Emitter |
| DS-3400D UK | 制造商:TRUST 功能描述:DESKTOP WIRELESS OPTICAL TRUST |
| DS3404FP000 | 制造商:Thomas & Betts 功能描述:30A,PLG,3P4W,MG,404,3P480V |
| DS3404FP000/JG63 | 制造商:Thomas & Betts 功能描述:30A,CON,3P4W,MG,404,3P480V,JG63,SC |
發布緊急采購，3分鐘左右您將得到回復。