- 您現在的位置：買賣IC網 > PDF目錄374668 > S5335DK (Applied Micro Circuits Corp.) PCI Bus Controller, 3.3V PDF資料下載
參數資料
| 型號： | S5335DK |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | PCI Bus Controller, 3.3V |
| 中文描述： | PCI總線控制器，3.3 |
| 文件頁數： | 92/189頁 |
| 文件大小： | 1193K |
| 代理商： | S5335DK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁當前第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁
S5335 – PCI Bus Controller, 3.3V
Revision 5.01 – November 30, 2005
Data Sheet
AMCC Confidential and Proprietary
DS1657 92
PCI BUS INTERFACE
This section describes the various events which occur
on the S5335 PCI bus interface. Since the S5335 con-
troller functions as both a target (slave) and an initiator
(master), signal timing detail is given for both situa-
tions this Section presents the signal relationships
involved in performing basic read or write transfers on
the PCI bus and also describes the different ways
these cycles may complete.
PCI BUS TRANSACTIONS
Because the PCI bus has multiplexed address/data
pins, AD[31:0], each PCI bus transaction consists of
two phases: Address and Data. An address phase is
defined by the clock period when the signal FRAME#
transitions from inactive (high) to active (low). During
the address phase, a bus command is also driven by
the initiator on signal pins C/BE[3:0]#. If the command
indicates a PCI read, the clock cycle following the
address phase is used to perform a “bus turn-around”
cycle. A turn-around cycle is a clock period in which
the AD bus is not driven by the initiator or the target
device. This is used to avoid PCI bus contention. For a
write command, a turn-around cycle is not needed,
and the bus goes directly from the address phase to
the data phase.
All PCI bus transactions consist of an address phase
(described above), followed by one or more data
phases. The address phase is only one PCI clock long
and the bus cycle information (address and command)
is latched internally by the S5335. The number of data
phases depends on how many data transfers are
desired or are possible with a given initiator-target pair.
A data phase consists of at least one PCI clock.
FRAME# is deasserted to indicate that the final data
phase of a PCI cycle is occurring. Wait states may be
added to any data phase (each wait state is one PCI
clock).
The PCI bus command presented on the C/BE[3:0]#
pins during the address phase can represent 16 possi-
ble states. Table 54 lists the PCI commands and
identifies those which are supported by the S5335
controller as a target and those which may be pro-
duced by the S5335 controller as an initiator. A “Yes”
in the “Supported As Target” column in Table 54 indi-
cates the S5335 controller asserts the signal
DEVSEL# when that command is issued along with
the appropriate PCI address. Two commands are sup-
ported by the S5335 controller as an initiator: Memory
Read and Memory Write.
The completion or termination of a PCI cycle can be
signaled in several ways. In most cases, the comple-
tion of the final data phase is indicated by the
assertion of ready signals from both the target
(TRDY#) and initiator (IRDY#) while FRAME# is inac-
tive. In some cases, the target is not be able to
continue or support a burst transfer and asserts the
STOP# signal. This is referred to as a target discon-
nect. There are also cases where an addressed
device does not exist, and the signal DEVSEL# never
becomes active. When no DEVSEL# is asserted in
response to a PCI cycle, the initiator is responsible for
ending the cycle. This is referred to as a master abort.
The bus is returned to the idle phase when both
FRAME# and IRDY# are deasserted.
相關PDF資料 |
PDF描述 |
|---|---|
| S5335QF | PCI Bus Controller, 3.3V |
| S5335QFAAB | PCI Bus Controller, 3.3V |
| S5566B | General Purpose Rectifier(通用整流器) |
| S5566G | General Purpose Rectifier(通用整流器) |
| S5566J | GENERAL PURPOSE RECTIFIER APPLICATIONS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S5335QF | 制造商:AppliedMicro 功能描述: |
| S5335QFAAB | 制造商:AppliedMicro 功能描述:PCI Bus Controller |
| S533-M04-F13A-E | 制造商:UNICORP 功能描述: |
| S-533-M04-F13-F | 制造商:UNICORP 功能描述: |
| S533-M04-F13-F | 制造商:UNICORP 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。