- 您現在的位置：買賣IC網 > PDF目錄374668 > S5335DK (Applied Micro Circuits Corp.) PCI Bus Controller, 3.3V PDF資料下載
參數資料
| 型號： | S5335DK |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | PCI Bus Controller, 3.3V |
| 中文描述： | PCI總線控制器，3.3 |
| 文件頁數： | 86/189頁 |
| 文件大小： | 1193K |
| 代理商： | S5335DK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁
S5335 – PCI Bus Controller, 3.3V
Revision 5.01 – November 30, 2005
Data Sheet
AMCC Confidential and Proprietary
DS1657 86
LOADING FROM SERIAL NV MEMORIES
SNV tied high indicates that a serial nv memory (or no
external device) is present. When serial nv memories
are used, data transfer is performed through a two-
wire, bidirectional data transfer protocol as defined by
commercial serial EEPROM/Flash offerings. These
devices have the advantages of low pin counts, small
package size, and economical price.
A serial nv memory is considered valid if the first serial
accesses contain the correct per-byte acknowledg-
ments (see Figure 41). If the serial per-byte
acknowledgment is not observed, the S5335 deter-
mines that no external serial nv memory is present
and the AMCC default Configuration Register values
are used.
Two pins are used to transfer data between the S5335
PCI controller and the external serial memory: a serial
clock pin, SCL, and a serial data pin, SDA. The serial
clock pin is an output from the S5335, and the serial
data pin is bidirectional. The serial clock is derived by
dividing the PCI bus clock by 512. This means that the
frequency of the serial clock is approximately 65 kHz
for a 33-MHz PCI bus clock.
Note: When a serial boot device is used, EA9 is de-
fined as a SCL divide by control pin.
If EA9 = 1 then SCL = PCLK/512
If EA9 = 0 then SCL = PCLK/8
This pin should be pulled high.
Communications with the serial memory involve sev-
eral clock transitions. A start event signals the
beginning of a transaction and is immediately followed
by an address transfer. Each address/data transfer
consists of 8 bits of information followed by a 1-bit
acknowledgment. When the exchange is complete, a
stop event is issued. Figure 39 shows the unique rela-
tionship defining both a start and stop event. Figure 40
shows the required timing for address/data with
respect to the serial clock.
For random accesses, the sequence involves one
clock to define the start of the sequence, eight clocks
to send the slave address and read/write command,
followed by a one-clock acknowledge, and so on. Fig-
ure 41 shows the sequence for a random write access
requiring 29 serial clock transitions. At the clock speed
for the S5335, this corresponds to one byte of data
transferred approximately every 0.5 milliseconds.
Read accesses may be either random or sequential.
Random read access requires a dummy write to load
the word address and require 39 serial clock transi-
tions. Figure 42 shows the sequence for a random
byte read.
To initialize the S5335 controller’s PCI Configuration
Registers, the smallest serial device necessary is a
128 x 8 organization. Although the S5335 controller
only requires 64 bytes, these bytes must begin at a 64-
byte address offset (0040h through 007Fh). This offset
constraint permits the configuration image to be
shared with a memory containing expansion BIOS
code and the necessary preamble to identify an
expansion BIOS. The largest serial device which may
be used is 2 Kbytes.
Table 51. Valid External Boot Memory Contents
Address
Data
Notes
0040h-41h
not FFFFh
This is the location that the S5335 PCI Controller will load a customized vendor ID. (FFFFh
is an illegal vendor ID.)
0050h
C2h, C1h or C0h
This is the least significant byte of the region which initializes the base address register #0
of the S5335 configuration register (Section 3.11). A value of C1h assigns the 16 DWORD
locations of the PCI operation registers into I/O space, a value of C0h defines memory
space, a value of C2h defines memory space below 1 Mbyte.
0051
FFh
Required.
0052h
E8h
Required.
0053h
10h
Required.
相關PDF資料 |
PDF描述 |
|---|---|
| S5335QF | PCI Bus Controller, 3.3V |
| S5335QFAAB | PCI Bus Controller, 3.3V |
| S5566B | General Purpose Rectifier(通用整流器) |
| S5566G | General Purpose Rectifier(通用整流器) |
| S5566J | GENERAL PURPOSE RECTIFIER APPLICATIONS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S5335QF | 制造商:AppliedMicro 功能描述: |
| S5335QFAAB | 制造商:AppliedMicro 功能描述:PCI Bus Controller |
| S533-M04-F13A-E | 制造商:UNICORP 功能描述: |
| S-533-M04-F13-F | 制造商:UNICORP 功能描述: |
| S533-M04-F13-F | 制造商:UNICORP 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。