- 您現在的位置：買賣IC網 > PDF目錄374668 > S5335DK (Applied Micro Circuits Corp.) PCI Bus Controller, 3.3V PDF資料下載
參數資料
| 型號： | S5335DK |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | PCI Bus Controller, 3.3V |
| 中文描述： | PCI總線控制器，3.3 |
| 文件頁數： | 25/189頁 |
| 文件大小： | 1193K |
| 代理商： | S5335DK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁
S5335 – PCI Bus Controller, 3.3V
Revision 5.01 – November 30, 2005
Data Sheet
AMCC Confidential and Proprietary
DS1657 25
SELECT#
in
Select for the Add-On interface. This signal must be driven low for any write or read access to the Add-
On interface registers. This signal must be stable during the assertion of command signals WR# or
RD#.
WR#
in
Write strobe. This pin, when asserted in conjunction with the SELECT# pin, causes the writing of one
of the internal registers. The specific register and operand size are identified through address pins
ADR[6:2] and the byte enables, BE[3:0]#.
RD#
in
Read strobe. This pin, when asserted in conjunction with the SELECT# pin, causes the reading of one
of the internal registers. The specific register and operand size are identified through address pins
ADR[6:2] and the byte enables BE[3:0]#.
MODE
in
This pin control whether the S5335 data accesses on the DQ bus are to be 32-bits wide (MODE = low)
or 16-bits wide (MODE = high). When in the 16 bit mode, the signal BE3# is reassigned as the address
signal ADR1. MODE has an internal 50k Ohm pull-up resistor.
Table 13. FIFO Access Pins
Signal
Type
Description
WRFIFO#
in
Write FIFO. This signal provides a method to directly write the FIFO without having to generate the
SELECT# signal or the ADR[6:2] value of [01000b] to access the FIFO. Access width is either 32 bits
or 16 bits depending on the data bus size available. This signal is intended for implementing PCI DMA
transfers with the Add-On system. WRFIFO# has an internal 50k Ohm pull-up resistor.
RDFIFO#
in
Read FIFO. This signal provides a method to directly read the FIFO without having to generate the
SELECT# signal or the ADR[6:2] value of [01000b] to access the FIFO. Access width is either 32 bits
or 16 bits, depending on the data bus size defined by the MODE pin. This signal is intended for imple-
menting PCI DMA transfers with the Add-On system. RDFIFO# has an internal 50k Ohm pull-up resis-
tor.
WRFULL
out
Write FIFO full. This pin indicates whether the Add-On-to-PCI bus FIFO is able to accept more data.
This pin is intended to be used to implement DMA hardware on the Add-On system bus. A logic low
output from this pin can be used to represent a DMA write (Add-On to-PCI FIFO) request.
RDEMPTY
out
Read FIFO Empty. This pin indicates whether the read FIFO (PCI-to-Add-On FIFO) contains data.
This pin is intended to be used by the Add-On system to control DMA transfers from the PCI bus to the
Add-On system bus. A logic low from this pin can be used to represent a DMA (PCI-to-Add-On FIFO)
request.
Table 14. Pass-Thru Interface Pins
Signal
Type
Description
PTATN#
out
Pass-Thru Attention. This signal identifies that an active PCI bus cycle has been decoded and data
must be read from or written to the Pass-Thru Data Register.
PTBURST#
out
Pass-Thru Burst. This signal identifies PCI bus operations involving the current Pass-Thru cycle as
requesting burst access.
PTRDY#
in
Pass-Thru Ready. This input indicates when Add-On logic has completed a Pass-Thru cycle and
another may be initiated.
PTNUM[1:0]
out
Pass-Thru Number. These signals identify which of the four base address registers decoded a Pass-
Thru bus activity. These bits are only meaningful when signal PTATN# is active. A value of 00 corre-
sponds to Base Address Register 1, a value of 01 for Base Address Register 2, and so on.
Table 12. Register Access Pins (Continued)
Signal
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| S5335QF | PCI Bus Controller, 3.3V |
| S5335QFAAB | PCI Bus Controller, 3.3V |
| S5566B | General Purpose Rectifier(通用整流器) |
| S5566G | General Purpose Rectifier(通用整流器) |
| S5566J | GENERAL PURPOSE RECTIFIER APPLICATIONS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S5335QF | 制造商:AppliedMicro 功能描述: |
| S5335QFAAB | 制造商:AppliedMicro 功能描述:PCI Bus Controller |
| S533-M04-F13A-E | 制造商:UNICORP 功能描述: |
| S-533-M04-F13-F | 制造商:UNICORP 功能描述: |
| S533-M04-F13-F | 制造商:UNICORP 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。