- 您現在的位置：買賣IC網 > PDF目錄374668 > S5335DK (Applied Micro Circuits Corp.) PCI Bus Controller, 3.3V PDF資料下載
參數資料
| 型號： | S5335DK |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | PCI Bus Controller, 3.3V |
| 中文描述： | PCI總線控制器，3.3 |
| 文件頁數： | 160/189頁 |
| 文件大?。?/td> | 1193K |
| 代理商： | S5335DK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁當前第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁
S5335 – PCI Bus Controller, 3.3V
Revision 5.01 – November 30, 2005
Data Sheet
AMCC Confidential and Proprietary
DS1657 160
To write data into the APTD Register, the PTBEn# out-
put and the BEn# input must both be asserted. The
following describes how APTD Register writes are
controlled:
Write BYTE3 if PTBE3# AND BE3# are asserted
Write BYTE2 if PTBE2# AND BE2# are asserted
Write BYTE1 if PTBE1# AND BE1# are asserted
Write BYTE0 if PTBE0# AND BE0# are asserted
After each byte is written into the Pass-Thru data reg-
ister, its corresponding PTBE[3:0]# output is
deasserted. This allows Add-On logic to monitor which
bytes have been written, and which bytes remain to be
written. When all bytes requested by the PCI initiator
have been written, the PTBE[3:0]# are all be deas-
serted, and the Add-On asserts PTRDY#.
Figure 93 shows Pass-Thru operation for a region
defined for an 8-bit Add-On bus interface. As the 8-bit
device is connected only to DQ[7:0], the device must
access APTD one byte at a time.
The PCI initiator has performed a 32-bit write of
08D49A30h to Pass-Thru region zero. PTBE[3:0]# are
all asserted. At clock 1, the Add-On begins reading the
APTD Register (asserting SELECT#, ADR[6:2], and
RD#). Add-On logic asserts BE0#, and BYTE0 of
APTD is driven on DQ[7:0]. At the rising edge of clock
2, BE0# is sampled by the S5335 and PTBE0# is
deasserted. PTBE[3:1]# are still asserted.
During clock 2, only BE1# is activated, and BYTE1 of
APTD is driven on DQ[7:0]. At the rising edge of clock
3, BE1# is sampled by the S5335 and PTBE1# is
deasserted. PTBE[3:2]# are still asserted.
This process continues until all bytes have been read
from the APTD Register. During clock 5, RD# is deas-
serted and PTRDY# is asserted. PTRDY# is sampled
by the S5335 at the rising edge of clock 6, and the cur-
rent data phase is completed. PTATN# is deasserted
and new data can be written from the PCI bus. In this
example, the byte enables are asserted, sequentially,
from BE0# to BE3#. This is not required, bytes may be
accessed in any order.
New data is written by the PCI initiator and is available
in the APTD Register during clock 7. RD# is asserted
and the byte enables are cycled again. With each new
data from the PCI bus, the Add-On sequences through
the byte enables to access APTD via DQ[7:0].
For 16-bit peripheral devices, the byte steering works
in the same way. Because the Add-On data bus is 16-
bits wide, only two 16-bit cycles are required to access
the entire APTD Register. Two byte enables can be
asserted during each access.
In Figure 93, RD# is held low and the byte enables are
changed each clock. This assumes the Add-On can
accept data at one byte per clock. This is the fastest
transfer possible. For slower devices, wait states may
be added.
As long as the byte enables remain in a given state,
the corresponding byte of the APTD Register is con-
nected to the DQ bus (the RD# or WR# pulse may
also be lengthened). Each access may be extended
for slower Add-On devices, but extending individual
data phases for Pass-Thru cycles may result in the
S5335 requesting retries by the initiator.
Figure 93. Pass-Thru Write to an 8-bit Add-On Device
Note: 8 Bit Mode BE’s are E, D, B, 7; 16 Bit Mode BE’s are C, 3.
10
11
12
13
9
8
7
6
5
4
3
2
3Ch
3Ch
2Ch
Fh
0h
1h
3h
7h
Fh
0h
1h
3h
7h
Fh
1
BPCLK
PTATN#
PTWR
PTBE[3:0]#
PTNUM[1:0]
PTBURST#
Fh
Bh
Eh
Dh
7h
Fh
Eh
Dh
Bh
7h
Fh
D4h
30h
9Ah
08h
DDh
CCh
BBh
AAh
ADDR
0
SELECT#
BE[3:0]#
PTADR#
PTRDY#
ADR[6:2]
RD#
DQ[7:0]
相關PDF資料 |
PDF描述 |
|---|---|
| S5335QF | PCI Bus Controller, 3.3V |
| S5335QFAAB | PCI Bus Controller, 3.3V |
| S5566B | General Purpose Rectifier(通用整流器) |
| S5566G | General Purpose Rectifier(通用整流器) |
| S5566J | GENERAL PURPOSE RECTIFIER APPLICATIONS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S5335QF | 制造商:AppliedMicro 功能描述: |
| S5335QFAAB | 制造商:AppliedMicro 功能描述:PCI Bus Controller |
| S533-M04-F13A-E | 制造商:UNICORP 功能描述: |
| S-533-M04-F13-F | 制造商:UNICORP 功能描述: |
| S533-M04-F13-F | 制造商:UNICORP 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。