參數資料
型號： AD9558/PCBZ
廠商： Analog Devices Inc
文件頁數： 48/104頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD9558
產品變化通告： AD9558 Minor Metal Mask Change 17/Apr/2012
設計資源： AD9558 Eval Brd BOM
AD9558 Schematic
標準包裝： 1
系列： *
AD9558
Data Sheet
Rev. B | Page 48 of 104
Programming the EEPROM to Configure an M Pin to
Control Synchronization of Clock Distribution
A special EEPROM loading sequence is required to use the
EEPROM to load the registers and to use an M pin to
enable/disable outputs.
To control the output sync function by using an M pin, perform
the following steps:
1. Enable the M pins by writing Register 0x0200 = 0x01.
2. Issue an I/O update (Register 0x0005 = 0x01).
3. Set the appropriate M pin function (see the Clock
Distribution Synchronization section for details).
If this sequence is not performed, a SYNC pulse is issued
automatically.
The following changes write Register 0x0200 first and then issue
an I/O update before writing the remaining M pin configuration
registers in Register 0x0201 to Register 0x0208.
The default EEPROM loading sequence from Register 0x0E10 to
Register 0x0E16 is unchanged. The following steps must be
inserted into the EEPROM storage sequence:
1. R0x0E17 = 0x00 # Write one byte
2. R0x0E18 = 0x02 # at Register 0x0200
3. R0x0E19 = 0x00 #
4. R0x0E1A = 0x80 # Op code for I/O
Update R0x0E1B = 0x10 # Transfer 17 instead of 18 bytes
5. R0x0E1C = 0x02 # Transfer starts at Register address
6. R0x0E1D = 0x01 # 0x0201 instead of 0x0200
The rest of the EEPROM loading sequence is the same as the
default EEPROM loading sequence, except that the register
address of the EEPROM storage sequence is shifted down four
bytes from the default. For example,
R0x0E1E = default value of Register 0x0E1A = 0x2E
R0x0E1F = default value of Register 0x0E1B = 0x03
R0x0E20 = default value of Register 0x0E1C = 0x00
…
R0x0E40 = default value of Register 0x0E1C = 0x3C = 0xFF
(end of data)
相關PDF資料
PDF描述
GBM22DSAH CONN EDGECARD 44POS R/A .156 SLD
DK-2632-03 CABLE FIBER OPTIC DUAL LC-SC 3M
GEM30DTAS CONN EDGECARD 60POS R/A .156 SLD
GMM12DRXI CONN EDGECARD 24POS DIP .156 SLD
P1330R-105K INDUCTOR POWER 1000.0UH SMD
相關代理商/技術參數
參數描述
AD9559 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PLL, Quad Input, Multiservice Line Card Adaptive Clock Translator
AD9559/PCBZ 功能描述:時鐘和定時器開發工具 Multi-protocol line card dual clock RoHS:否 制造商:Texas Instruments 產品:Evaluation Modules 類型:Clock Conditioners 工具用于評估:LMK04100B 頻率:122.8 MHz 工作電源電壓:3.3 V
AD9559BCPZ 功能描述:時鐘發生器及支持產品 Multi-protocol line card dual clock RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
AD9559BCPZ-REEL7 功能描述:時鐘發生器及支持產品 Multi-protocol line card dual clock RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
AD9559PCBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PLL, Quad Input, Multiservice Line Card Adaptive Clock Translator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*