參數資料
型號: DS3131
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: Telecom IC:Other
英文描述: SPECIALTY TELECOM CIRCUIT, PBGA256
封裝: 27 X 27 MM, PLASTIC, BGA-256
文件頁數: 90/174頁
文件大小: 1261K
代理商: DS3131
DS3131
22 of 174
Signal Name:
LRD
LRD (LDS
LDS
LDS)
Signal Description:
Local Bus Read Enable (Local Bus Data Strobe)
Signal Type:
Input/Output (three-state capable)
In the PCI bridge mode (LMS = 0), this active-low output signal is asserted on the rising edge of LCLK. In Intel
mode (LIM = 0), it is asserted when data is to be read from the local bus. In Motorola mode (LIM = 1), the rising
edge is used to write data into the slave device. If bus arbitration is enabled through the LARBE control bit in the
LBBMC register, this signal is three-stated when the local bus is not currently involved in a bus transaction and
driven when a bus transaction is active. When bus arbitration is disabled, this signal is always driven. In
configuration mode (LMS = 1), this signal is an active-low input that is sampled on the rising edge of LCLK. In
Intel mode (LIM = 0), it determines when data is to be read from the device. In Motorola mode (LIM = 1), the
rising edge writes data into the device.
Signal Name:
LINT
Signal Description:
Local Bus Interrupt
Signal Type:
Input/Output (open drain)
In the PCI bridge mode (LMS = 0), this active-low signal is an input that is sampled on the rising edge of LCLK.
If asserted and unmasked, this signal causes an interrupt at the PCI bus through the PINTA signal. If not used in
PCI bridge mode, this signal should be connected high. In configuration mode (LMS = 1), this signal is an open-
drain output that is forced low if one or more unmasked interrupt sources within the device is active. The signal
remains low until either the interrupt is serviced or masked.
Signal Name:
LRDY
Signal Description:
Local Bus PCI Bridge Ready (PCI Bridge Mode Only)
Signal Type:
Input
This active-low signal is sampled on the rising edge of LCLK to determine when a bus transaction is complete.
This signal is only examined when a bus transaction is taking place. This signal is ignored when the local bus is in
configuration mode (LMS = 1) and should be connected high.
Signal Name:
LHLDA (LBG
LBG
LBG)
Signal Description:
Local Bus Hold Acknowledge (Local Bus Grant) (PCI Bridge Mode Only)
Signal Type:
Input
This input signal is sampled on the rising edge of LCLK to determine when the device has been granted access to
the bus. In Intel mode (LIM = 0), this is an active-high signal; in Motorola mode (LIM = 1) this is an active-low
signal. This signal is ignored and should be connected high when the local bus is in configuration mode
(LMS = 1). Also, in PCI bridge mode (LMS = 0), this signal should be wired deasserted when the local bus
arbitration is disabled through the LBBMC register.
Signal Name:
LHOLD (LBR
LBR
LBR)
Signal Description:
Local Bus Hold (Local Bus Request) (PCI Bridge Mode Only)
Signal Type:
Output
This signal is asserted when the DS3131 is attempting to control the local bus. In Intel mode (LIM = 0), this signal
is an active-high signal; in Motorola mode (LIM = 1) this signal is an active-low signal. It is deasserted
concurrently with LBGACK. This signal is three-stated when the local bus is in configuration mode (LMS = 1)
and also in PCI bridge mode (LMS = 0) when the local bus arbitration is disabled through the LBBMC register.
Signal Name:
LBGACK
Signal Description:
Local Bus Grant Acknowledge (PCI Bridge Mode Only)
Signal Type:
Output (three-state capable)
This active-low signal is asserted when the local bus hold-acknowledge/bus grant signal (LHLDA/LBG) has been
detected and continues its assertion for a programmable (32 to 1,048,576) number of LCLKs, based on the local
bus arbitration timer setting in the LBBMC register. This signal is three-stated when the local bus is in
configuration mode (LMS = 1).
相關PDF資料
PDF描述
DS3134 DATACOM, FRAMER, PBGA256
DS3150QN DATACOM, PCM TRANSCEIVER, PQCC28
DS3150Q DATACOM, PCM TRANSCEIVER, PQCC28
DS3150TN DATACOM, PCM TRANSCEIVER, PDIP48
DS3150T DATACOM, PCM TRANSCEIVER, PQFP48
相關代理商/技術參數
參數描述
DS3131DK 功能描述:通信集成電路 - 若干 RoHS:否 制造商:Maxim Integrated 類型:Transport Devices 封裝 / 箱體:TECSBGA-256 數據速率:100 Mbps 電源電壓-最大:1.89 V, 3.465 V 電源電壓-最小:1.71 V, 3.135 V 電源電流:50 mA, 225 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube
DS3134 功能描述:IC CTRLR HDLC CHATEAU 256-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A
DS-313PIN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Miscellaneous
DS-313-PIN 功能描述:信號調節 RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel
DS31400 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:8-Input, 14-Output, Dual DPLL Timing IC with Sub-ps Output Jitter