參數資料
型號: DS3131
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: Telecom IC:Other
英文描述: SPECIALTY TELECOM CIRCUIT, PBGA256
封裝: 27 X 27 MM, PLASTIC, BGA-256
文件頁數: 89/174頁
文件大小: 1261K
代理商: DS3131
DS3131
21 of 174
Signal Name:
LBPXS
Signal Description:
Local Bus or Port Extension Select
Signal Type:
Input (with internal 10k pullup)
This signal must be left open-circuited (or connected high) to activate and enable the local bus. When this signal is
connected low, the local bus is disabled and its signals are redefined to support 12 bit-synchronous HDLC
controllers on ports 28 to 39 (Table 3-A).
0 = local bus disabled
1 (or open -ircuited) = local bus enabled
Signal Name:
LD0 to LD15
Signal Description:
Local Bus Nonmultiplexed Data Bus
Signal Type:
Input/Output (three-state capable)
In PCI bridge mode (LMS = 0), data from/to the PCI bus can be transferred to/from these signals. When writing
data to the local bus, these signals are outputs and updated on the rising edge of LCLK. When reading data from
the local bus, these signals are inputs, which are sampled on the rising edge of LCLK. Depending on the assertion
of the PCI byte enables (PCBE0 to PCBE3) and the local bus-width (LBW) control bit in the local bus bridge
mode control register (LBBMC), this data bus uses all 16 bits (LD[15:0]) or just the lower 8 bits (LD[7:0]) or the
upper 8 bits (LD[15:8]). If the upper LD bits (LD[15:8]) are used, then the local bus high-enable signal (LBHE) is
asserted during the bus transaction. If the local bus is not currently involved in a bus transaction, all 16 signals are
three-stated. When reading data from the local bus, these signals are outputs that are updated on the rising edge of
LCLK. When writing data to the local bus, these signals become inputs, which are sampled on the rising edge of
LCLK. In configuration mode (LMS = 1), the external host configures the device and obtains real-time status
information about the device through these signals. Only the 16-bit bus width is allowed (i.e., byte addressing is
not available).
Signal Name:
LA0 to LA19
Signal Description:
Local Bus Nonmultiplexed Address Bus
Signal Type:
Input/Output (three-state capable)
In the PCI bridge mode (LMS = 0), these signals are outputs that are asserted on the rising edge of LCLK to
indicate which address is written to or read from. If bus arbitration is enabled through the local bus arbitration
(LARBE) control bit in the LBBMC register, these signals are three-stated when the local bus is not currently
involved in a bus transaction and driven when a bus transaction is active. When bus arbitration is disabled, these
signals are always driven. These signals are sampled on the rising edge of LCLK to determine the internal device
configuration register that the external host wishes to access. In configuration mode (LMS = 1), these signals are
inputs and only the bottom 16 bits (LA[15:0]) are active; the upper four (LA[19:16]) are ignored and should be
connected low.
Signal Name:
LWR
LWR (LR/W
W
W)
Signal Description:
Local Bus Write Enable (Local Bus Read/Write Select)
Signal Type:
Input/Output (three-state capable)
In the PCI bridge mode (LMS = 0), this output signal is asserted on the rising edge of LCLK. In Intel mode
(LIM = 0), it is asserted when data is to be written to the local bus. In Motorola mode (LIM = 1), this signal
determines whether a read or write is to occur. If bus arbitration is enabled through the LARBE control bit in the
LBBMC register, this signal is three-stated when the local bus is not currently involved in a bus transaction and
driven when a bus transaction is active. When bus arbitration is disabled, this signal is always driven. In
configuration mode (LMS = 1), this signal is sampled on the rising edge of LCLK. In Intel mode (LIM = 0), it
determines when data is to be written to the device. In Motorola mode (LIM = 1), this signal determines whether a
read or write is to occur.
相關PDF資料
PDF描述
DS3134 DATACOM, FRAMER, PBGA256
DS3150QN DATACOM, PCM TRANSCEIVER, PQCC28
DS3150Q DATACOM, PCM TRANSCEIVER, PQCC28
DS3150TN DATACOM, PCM TRANSCEIVER, PDIP48
DS3150T DATACOM, PCM TRANSCEIVER, PQFP48
相關代理商/技術參數
參數描述
DS3131DK 功能描述:通信集成電路 - 若干 RoHS:否 制造商:Maxim Integrated 類型:Transport Devices 封裝 / 箱體:TECSBGA-256 數據速率:100 Mbps 電源電壓-最大:1.89 V, 3.465 V 電源電壓-最小:1.71 V, 3.135 V 電源電流:50 mA, 225 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube
DS3134 功能描述:IC CTRLR HDLC CHATEAU 256-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A
DS-313PIN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Miscellaneous
DS-313-PIN 功能描述:信號調節 RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel
DS31400 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:8-Input, 14-Output, Dual DPLL Timing IC with Sub-ps Output Jitter