參數資料
型號: DS3131
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: Telecom IC:Other
英文描述: SPECIALTY TELECOM CIRCUIT, PBGA256
封裝: 27 X 27 MM, PLASTIC, BGA-256
文件頁數: 49/174頁
文件大小: 1261K
代理商: DS3131
DS3131
142 of 174
If the local bus is used as 16-bit bus, then the LBW control bit must be set to 0. In 16-bit accesses, the
host can either perform a 16-bit access or an 8-bit access by asserting the appropriate PCBE signals (see
Table 11-C). For 16-bit access, the host enables the combination of either PCBE0/PCBE1 or
PCBE2/PCBE3 and the local bus block maps the word from/to the PCI bus to/from the LD[15:0]
signals. For 8-bit access in the 16-bit bus mode, the host must assert just one of the PCBE0 to PCBE3
signals. If the host asserts a combination of PCBE signals not supported by the local bus, the local bus
rejects the access and the PCI block returns a target abort to the host. See Section 10 for details on a
target abort. Section 11.3 contains a number of timing examples for the local bus.
Table 11-C. Local Bus 16-Bit Width Address, LD,
LBHE
LBHE Setting
PCBE
PCBE [3:0]
8/16
A1
A0
LD[15:8]
LD[7:0]
LBHE
1110
8
0
Active
1
1101
8
0
1
Active
0
1100
16
0
Active
0
1011
8
1
0
Active
1
0111
8
1
Active
0
0011
16
1
0
Active
0
Note 1:
All other possible states for
PCBE cause the device to return a target abort to the host.
Note 2:
The 16-bit data picked from the PCI bus is routed/sampled to/from the LD[7:0] and LD[15:8] signal lines as shown.
Note 3:
If no
PCBE signals are asserted during an access, a target abort is not returned and no transaction occurs on the local bus.
Bridge Mode Bus Arbitration
In bridge mode, the local bus has the ability to arbitrate for bus access. In order for this feature to
operate, the host must access the PCI bridge mode control register (LBBMC) and enable it through the
LARBE control bit (the default is bus arbitration disabled). If bus arbitration is enabled, then, before a
bus transaction can occur, the local bus first requests bus access by asserting the LHOLD (LBR) signal
and then waits for the bus to be granted from the local bus arbiter by sensing that the LHLDA (LBG) has
been asserted. If the host on the PCI bus attempts a local bus access when the local bus is not granted by
the local bus master (LBGACK is deasserted), the local bus block immediately informs the host by
issuing a PCI target retry that the local bus is busy and cannot be accessed at that time (in other words,
come back later). See Section 10 for details about the PCI target retry. When this happens, the local bus
block does not attempt the bus access and keeps the LA, LD, LBHE, LWR (LR/W), and LRD (LDS)
signals three-stated.
If the host attempts a local bus access when the bus is busy, the local bus block requests bus access, and,
after it has been granted, it seizes the bus for the time programmed into the local bus arbitration timer
(LAT0 to LAT3 in the LBBMC register), which can be from 32 to 1,048,576 clocks. As long as the local
bus has been granted and the arbitration timer has at least 16 clocks left, the host is allowed to access the
local bus. See Figure 11-4 and the timing examples in Section 11.3 for more details.
Bridge Mode Bus Transaction Timing
When the local bus is operated in PCI bridge mode, the bus transaction time can be determined either
from an external ready signal (LRDY) or from the PCI bridge mode control register (LBBMC), which
allows a bus transaction time of 1 to 11 LCLK cycles. If the total access time to the local bus exceeds 16
PCLK cycles, the PCI access times out and a PCI target retry is sent to the host. This only occurs when
LRDY has not been detected within 9 clocks. If this happens, the local bus error (LBE) status bit in the
status master (SM) register is set. Additional details about the LBE status bit can be found in Section 5.
More details about transaction timing can be found in Figure 10-4 and the timing examples in
Section 11.3.
相關PDF資料
PDF描述
DS3134 DATACOM, FRAMER, PBGA256
DS3150QN DATACOM, PCM TRANSCEIVER, PQCC28
DS3150Q DATACOM, PCM TRANSCEIVER, PQCC28
DS3150TN DATACOM, PCM TRANSCEIVER, PDIP48
DS3150T DATACOM, PCM TRANSCEIVER, PQFP48
相關代理商/技術參數
參數描述
DS3131DK 功能描述:通信集成電路 - 若干 RoHS:否 制造商:Maxim Integrated 類型:Transport Devices 封裝 / 箱體:TECSBGA-256 數據速率:100 Mbps 電源電壓-最大:1.89 V, 3.465 V 電源電壓-最小:1.71 V, 3.135 V 電源電流:50 mA, 225 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube
DS3134 功能描述:IC CTRLR HDLC CHATEAU 256-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A
DS-313PIN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Miscellaneous
DS-313-PIN 功能描述:信號調節 RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel
DS31400 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:8-Input, 14-Output, Dual DPLL Timing IC with Sub-ps Output Jitter