- 您現在的位置：買賣IC網 > PDF目錄11203 > ADUC7032BSTZ-88-RL (Analog Devices Inc)IC MCU 96K FLASH DUAL 48LQFP PDF資料下載
參數資料
| 型號： | ADUC7032BSTZ-88-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 85/120頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 96K FLASH DUAL 48LQFP |
| 標準包裝： | 2,000 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 連通性： | LIN，SPI，UART/USART |
| 外圍設備： | POR，PSM，溫度傳感器，WDT |
| 輸入/輸出數： | 9 |
| 程序存儲器容量： | 96KB（48K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1.5K x 32 |
| 電壓 - 電源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 數據轉換器： | A/D 2x16b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 105°C |
| 封裝/外殼： | 48-LQFP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
ADuC7032-8L
Rev. A | Page 67 of 120
PROCESSOR REFERENCE PERIPHERALS
INTERRUPT SYSTEM
There are 16 interrupt sources on the ADuC7032-8L that are
controlled by the interrupt controller. Most interrupts are
generated from the on-chip peripherals such as the ADC,
UART, and so on. The ARM7TDMI CPU core recognizes
interrupts as only one of two types: a normal interrupt request
(IRQ) and a fast interrupt request (FIQ). All the interrupts can
be masked separately.
The control and configuration of the interrupt system are
managed through nine interrupt-related registers, four
dedicated to IRQ and four dedicated to FIQ. An additional
MMR is used to select the programmed interrupt source. The
bits in each IRQ and FIQ register represent the same interrupt
source, as shown in Table 51.
IRQSTA/FIQSTA should be saved immediately upon entering
the interrupt service routine (ISR) to ensure that all valid
interrupt sources are serviced.
The interrupt generation route through the ARM7TDMI core is
shown in Figure 29.
Consider the example of Timer0, which is configured to
generate a timeout every 1 ms. After the first 1 ms timeout,
FIQSIG/IRQSIG[2] is set and can be cleared only by writing to
T0CLRI.
If Timer0 is not enabled in either IRQEN or FIQEN,
FIQSTA/IRQSTA[2] is not set and an interrupt does not occur.
If Timer0 is enabled in either IRQEN or FIQEN, then
FIQSTA/IRQSTA[2] is set and either an FIQ or an IRQ
interrupt occurs.
Note that the IRQ and FIQ interrupt bit definitions in the CPSR
control interrupt recognition by the ARM core only, not by the
peripherals. For example, if Timer2 is configured to generate an
IRQ via IRQEN, the IRQ interrupt bit is set (disabled) in the
CPSR, and the ADuC7032-8L is powered down. When an
interrupt occurs, the peripherals power up, but the ARM core
remains powered down. This is equivalent to POWCON =
0x71. The ARM core can be powered up only by a reset event if
this occurs.
Table 51. IRQ/FIQ MMRs Bit Designations
Bit
Description
Comments
0
All interrupts OR’ed (FIQ only).
1
SWI is not used in IRQEN/CLR and FIQEN/CLR.
2
Timer0.
See the Timer0—Lifetime Timer section.
3
Timer1.
See the Timer1 section.
4
Timer2 or Wake-Up Timer.
See the Timer2—Wake-Up Timer section.
5
Timer3 or Watchdog Timer.
See the Timer3—Watchdog Timer section.
6
Reserved. Should be written as 0.
7
LIN Hardware.
See the LIN (Local Interconnect Network) Interface section
8
Flash/EE Interrupt.
See the Flash/EE Control Interface section.
9
PLL Lock.
See the ADUC7032-8L System Clocks section.
10
ADC.
See the 16-Bit, Sigma-Delta Analog-to-Digital Converters section.
11
UART.
See the UART Serial Interface section.
12
SPI Master.
See the Serial Peripheral Interface section.
13
XIRQ0 (GPIO IRQ 0).
See the General-Purpose I/O section.
14
XIRQ1 (GPIO IRQ 1).
See the General-Purpose I/O section.
15
Reserved. Should be written as 0.
16
IRQ3. High voltage IRQ.
High voltage interrupt; see the High Voltage Peripheral Control Interface section
17
SPI Slave.
18
XIRQ4 (GPIO IRQ 4).
See the General-Purpose I/O section.
19
XIRQ5 (GPIO IRQ 5).
See the General-Purpose I/O section.
相關PDF資料 |
PDF描述 |
|---|---|
| AT91R40008-66AU-999 | IC MCU 32BIT RISC 100LQFP |
| ADUC7024BSTZ62-RL | IC MCU 12BIT 1MSPS UART 64-LQFP |
| VE-B33-IW-F3 | CONVERTER MOD DC/DC 24V 100W |
| VE-B33-IW-F1 | CONVERTER MOD DC/DC 24V 100W |
| VE-B34-IX-F3 | CONVERTER MOD DC/DC 48V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7032BSTZ-8L | 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Trays |
| ADUC7032BSTZ-8L-RL | 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Tape and Reel |
| ADUC7032BSTZ-8V | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| ADUC7032BSTZ-8V-RL | 功能描述:IC BATTERY SENSOR PREC 48-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:1,500 系列:AVR® ATtiny 核心處理器:AVR 芯體尺寸:8-位 速度:16MHz 連通性:I²C，LIN，SPI，UART/USART，USI 外圍設備:欠壓檢測/復位，POR，PWM，溫度傳感器，WDT 輸入/輸出數:16 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:帶卷 (TR) |
| ADUC7033 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive |
發布緊急采購，3分鐘左右您將得到回復。