參數資料
型號： ADUC7032BSTZ-88-RL
廠商： Analog Devices Inc
文件頁數： 76/120頁
文件大?。?/td> 0K
描述： IC MCU 96K FLASH DUAL 48LQFP
標準包裝： 2,000
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 20.48MHz
連通性： LIN，SPI，UART/USART
外圍設備： POR，PSM，溫度傳感器，WDT
輸入/輸出數： 9
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 1.5K x 32
電壓 - 電源 (Vcc/Vdd)： 3.5 V ~ 18 V
數據轉換器： A/D 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 105°C
封裝/外殼： 48-LQFP
包裝： 帶卷 (TR)
ADuC7032-8L
Rev. A | Page 59 of 120
A factory or end-of-line calibration for the I-ADC is a two-step
procedure.
1.
Apply 0 A current.
Configure the ADC in the required PGA setting and so on,
and write to ADCMDE[2:0] to perform a system zero-scale
calibration. This writes a new offset calibration value into
ADC0OF.
2.
Apply a full-scale current for the selected PGA setting.
Write to ADCMDE to perform a system full-scale calibration.
This writes a new gain calibration value into ADC0GN.
Understanding the Offset and Gain Calibration Registers
The output of the average block in the ADC signal flow (described
previously after the digital filter and before the offset and gain
scaling can be considered to be a fractional number with a span,
for a ±full-scale input of approximately ±0.75. The span is less
than ±1.0 because there is attenuation in the modulator to accom-
modate some overrange capacity on the input signal. The exact
value of the attenuation varies slightly from part to part because
of manufacturing tolerances.
The offset coefficient is read from the ADC0OF calibration
register. This value is a 16-bit twos complement number. The
range of this number, in terms of the signal chain, is effectively
±1.0. The value of 1 LSB of the ADC0OF register is not, therefore,
the same as 1 LSB of ADC0DAT.
A positive value of ADC0OF indicates that the offset is subtracted
from the output of the filter, and a negative value of ADC0OF
indicates that the offset is added to the output of the filter. The
nominal value of this register is 0x0000, indicating zero offset is to
be removed. The actual offset of the ADC may vary slightly from
part to part and at different PGA gains. The offset within the
ADC is minimized if chop mode is active (ADCFLT[15] = 1).
The gain coefficient is a unitless scaling factor. The 16-bit value
in this register is divided by 16,384 and then multiplied by the
offset-corrected value. The nominal value of this register equals
0x5555, which corresponds to a multiplication factor of 1.3333.
This scales the nominal ±0.75 signal to produce a full-scale output
signal of ±1.0, which is checked for overflow/underflow and
converted to twos complement or unipolar mode, as appropriate,
before being output to the data register.
The actual gain, and the required scaling coefficient for zero
gain error, vary slightly from part to part, and at different PGA
settings and in normal/low power mode. The value downloaded
into ADC0GN at power-on/reset represents the scaling factor
for a PGA gain = 1. There is some level of gain error if this value
is used at different PGA settings. User code can overwrite the
calibration coefficients or run ADC calibrations to correct the
gain error at the PGA setting in use.
In summary, the simplified ADC transfer function can be
described as
ADCGNNOM
ADCGN
ADCOF
VREF
PGA
VIN
ADCOUT
×
×
=
This equation is valid for both the voltage and temperature
channel ADCs.
For the current channel ADC
ADCGNNOM
ADCGN
ADCOF
K
VREF
PGA
VIN
ADCOUT
×
×
×
=
where K is dependent on the PGA gain setting and ADC mode.
Normal Mode
For PGA gains of 1, 4, 8, 16, 32, and 64, the K factor is 1. For
PGA gains of 2 and 128, the K factor is 2. For a PGA gain of
256, the K factor is 4. For a PGA gain of 512, the K factor is 8.
Low Power Mode
The PGA gain is set to 128, and the K factor is 32.
Low Power Plus Mode
The K factor is 8.
In low power and low power plus mode, the K factor doubles if
(REG_AVDD)/2 is used as the reference.
ADC DIAGNOSTICS
The ADuC7032-8L features diagnostic capability on all three
ADCs.
Current ADC Diagnostics
The ADuC7032-8L features the capability to detect open-circuit
conditions on the application board. This is accomplished using
the two current sources on IIN+ and IIN, which is controlled
via ADC0CON[14:13].
Note that these current sources have a tolerance of ±30%. A PGA
gain equal to or greater than 2 (ADC0CON[3:0] ≥ 0001) must
be used when current sources are enabled.
Temperature ADC Diagnostics
The ADuC7032-8L features the capability to detect open-circuit
conditions on the temperature channel inputs. This is accom-
plished using the two current sources on VTEMP and GND_SW,
which is controlled via ADC2CON[14:13].
Note that the current sources have a tolerance of ±30%.
相關PDF資料
PDF描述
AT91R40008-66AU-999 IC MCU 32BIT RISC 100LQFP
ADUC7024BSTZ62-RL IC MCU 12BIT 1MSPS UART 64-LQFP
VE-B33-IW-F3 CONVERTER MOD DC/DC 24V 100W
VE-B33-IW-F1 CONVERTER MOD DC/DC 24V 100W
VE-B34-IX-F3 CONVERTER MOD DC/DC 48V 75W
相關代理商/技術參數
參數描述
ADUC7032BSTZ-8L 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Trays
ADUC7032BSTZ-8L-RL 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Tape and Reel
ADUC7032BSTZ-8V 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述:
ADUC7032BSTZ-8V-RL 功能描述:IC BATTERY SENSOR PREC 48-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:1,500 系列:AVR® ATtiny 核心處理器:AVR 芯體尺寸:8-位 速度:16MHz 連通性:I²C，LIN，SPI，UART/USART，USI 外圍設備:欠壓檢測/復位，POR，PWM，溫度傳感器，WDT 輸入/輸出數:16 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:帶卷 (TR)
ADUC7033 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*