參數資料
型號： ADUC7032BSTZ-88-RL
廠商： Analog Devices Inc
文件頁數： 71/120頁
文件大小： 0K
描述： IC MCU 96K FLASH DUAL 48LQFP
標準包裝： 2,000
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 20.48MHz
連通性： LIN，SPI，UART/USART
外圍設備： POR，PSM，溫度傳感器，WDT
輸入/輸出數： 9
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 1.5K x 32
電壓 - 電源 (Vcc/Vdd)： 3.5 V ~ 18 V
數據轉換器： A/D 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 105°C
封裝/外殼： 48-LQFP
包裝： 帶卷 (TR)
ADuC7032-8L
Rev. A | Page 54 of 120
Current Channel ADC Threshold Count Register
Name:
ADC0THV
Address:
0xFFFF0558
Default Value:
0x00
Access:
Read only
Function:
This 8-bit MMR is incremented every time the
absolute value of an I-ADC conversion result |I| ≥ ADC0TH.
This register is decremented or reset to 0 every time the absolute
value of an I-ADC conversion result |I| < ADC0TH. The configu-
ration of this function is enabled via the current channel ADC
comparator bits in the ADCCFG MMR.
Current Channel ADC Accumulator Register
Name:
ADC0ACC
Address:
0xFFFF055C
Default Value:
0x00000000
Access:
Read only
Function:
This 32-bit MMR holds the current channel accumu-
lator value. The I-ADC ready bit in the ADCSTA MMR should
be used to determine when it is safe to read this MMR. The
MMR value is reset to 0 by disabling the accumulator in the
ADCCFG MMR or reconfiguring the current channel ADC.
Current Channel ADC Accumulator Threshold Register
Name:
ADC0ATH
Address:
0xFFFF0560
Default Value:
0x00000000
Access:
Read/write
Function:
This 32-bit MMR sets the threshold against which
the accumulated value of the I-ADC results is compared. In
unipolar mode, ADC0ATH [15:0] are compared and in twos
complement mode, ADC0ATH[14:0] are compared.
Low Power Voltage Reference Scaling Factor Register
Name:
ADCREF
Address:
0xFFFF057C
Default Value:
Part-specific, factory programmed
Access:
Read/write
Function:
This MMR allows user code to correct for the initial
error of the LPM reference. Value 0x8000 corresponds to no
error when compared to the normal mode reference. If the LPM
voltage reference is 1% below 1.200 V, the value of ADCREF is
approximately 0x7EB9. If the LPM voltage reference is 1% above
1.200 V, the value of ADCREF is approximately 0x8147.
This register corrects the effective value of the LPM reference at
the temperature at which the reference is measured during the
Analog Devices, Inc., production flow, which is 35°C. There is
no change to the temperature coefficient of the LPM reference
when using the ADCREF MMR.
This register should not be used if the precision reference is
being used in low power mode (if ADCMDE[5] is set).
ADC POWER MODES OF OPERATION
The ADCs can be configured into various reduced or full power
modes of operation by configuring ADCMDE[4:3] as appropriate.
The ARM7 MCU can itself also be configured in low power modes
of operation (POWCON[5:3]). The core power modes are inde-
pendently controlled and are not related to the ADC power modes
described in this section. The ADC power modes of operation are
described in more detail in the following paragraphs.
Every I-ADC result can also be compared to a preset threshold
level (ADC0TH), as configured via ADCCFG[4:3]. An MCU
interrupt is generated if the absolute (sign-independent) value
of the ADC result is greater than the preprogrammed comparator
threshold level. An extended function of this comparator
function allows user code to configure a threshold counter
(ADC0THV) that monitors the number of I-ADC results that
have occurred above or below the preset threshold level. Again,
an ADC interrupt is generated once the threshold counter
reaches a preset value (ADC0TCL).
Finally, a 32-bit accumulator (ADC0ACC) function can be
configured (ADCCFG[6:5]) allowing the I-ADC to add (or
subtract) multiple I-ADC sample results. User code can read
the accumulated value directly (via ADC0ACC) without any
further software processing.
ADC Startup Procedure
Before beginning the conversion process, the following
procedure should be followed:
1.
Configure the I-ADC to low power mode (ADC0CON =
0x8007; ADCMDE = 0x09).
2.
Delay for 200 μs.
3.
Switch the I-ADC into idle mode
(ADCMDE = 0x03), leaving ADC0CON unchanged.
If the voltage or temperature channels are to be used,
they should be enabled at this time.
4.
Delay for 1 ms.
5.
Switch ADCMDE to the desired mode, for example,
ADCMDE = 0x1.
ADC Normal Power Mode
In normal mode, the current and voltage/temperature channels
are fully enabled. The ADC modulator clock is 512 kHz and
enables the ADCs to provide regular conversion results at a rate
of between 4 Hz and 8 kHz (see Table 40 for the ADCFLT MMR
bit designations). Both channels are under full control of the
MCU and can be reconfigured at any time. The default ADC
update rate for all channels in this mode is 1.0 kHz.
相關PDF資料
PDF描述
AT91R40008-66AU-999 IC MCU 32BIT RISC 100LQFP
ADUC7024BSTZ62-RL IC MCU 12BIT 1MSPS UART 64-LQFP
VE-B33-IW-F3 CONVERTER MOD DC/DC 24V 100W
VE-B33-IW-F1 CONVERTER MOD DC/DC 24V 100W
VE-B34-IX-F3 CONVERTER MOD DC/DC 48V 75W
相關代理商/技術參數
參數描述
ADUC7032BSTZ-8L 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Trays
ADUC7032BSTZ-8L-RL 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Tape and Reel
ADUC7032BSTZ-8V 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述:
ADUC7032BSTZ-8V-RL 功能描述:IC BATTERY SENSOR PREC 48-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:1,500 系列:AVR® ATtiny 核心處理器:AVR 芯體尺寸:8-位 速度:16MHz 連通性:I²C，LIN，SPI，UART/USART，USI 外圍設備:欠壓檢測/復位，POR，PWM，溫度傳感器，WDT 輸入/輸出數:16 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:帶卷 (TR)
ADUC7033 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*