- 您現在的位置：買賣IC網 > PDF目錄378055 > PM6344 (PMC-SIERRA INC) Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 PDF資料下載
參數資料
| 型號： | PM6344 |
| 廠商： | PMC-SIERRA INC |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| 中文描述： | DATACOM, FRAMER, PQFP128 |
| 封裝： | 20 X 14 MM, PLASTIC, QFP-128 |
| 文件頁數： | 211/256頁 |
| 文件大?。?/td> | 1030K |
| 代理商： | PM6344 |
STANDARD PRODUCT
PMC-Sierra, Inc.
PM6344 EQUAD
PMC-951013
ISSUE 5
QUADRUPLE E1 FRAMER
198
Figure 24
- RFDL Normal Data and Abort Sequence
Serial Data
extracted from
ESF FDL
RDLINT[x]
RDLEOM[x]
D[7:0]
Flag
D1
D2
D3
Dn
R
C1
C2
Flag
D1
B1
B2 B3
D1
Dn-2
Dn-1
Dn
B1
B2 B3
D2
Dn-1
Dn-3
D1 B1
ABORT
EOM
EOM
B1
R Abort
This diagram shows the relationship between RFDL inputs and outputs for the
case where interrupts are programmed to occur when one byte is present in the
FIFO buffer. The RFDL is assumed to be operating in the interrupt driven mode.
Each read shown is composed of two register reads: first a read of the RFDL
Data Register, followed by a read of the RFDL Status Register. A read of the
RFDL Data Register sets the RDLINT[x] output to low if no more data exists in
the FIFO buffer. The status of the FE bit returned in the RFDL Status Register
read will indicate the FIFO buffer fill status as well. The RFDL Data Register read
Dn-2 is shown to occur after two bytes have been written into the buffer. The
RDLINT[x] output does not go low after the first RFDL Data Register read
because a data byte still remains to be read. The RDLINT[x] output goes low
after RFDL Data Register read Dn-1. The FE bit will be logic 0 in RFDL Status
Register read Dn-2 and logic 1 in RFDL Status Register read Dn-1.
The RDLEOM[x] output goes high as soon as the last byte in the frame is read
from the RFDL Data Register. The RDLINT[x] output will go low if the FIFO
buffer is empty. The next RFDL Status Register read will return a value of logic 1
for the EOM and FLG bits, and cause the RDLEOM[x] output of the RFDL to
return low.
In the next frame, the first data byte is received, and after a delay of ten bit
periods, it is written to the FIFO buffer, and read by the processor after the
interrupt. When the abort sequence is detected, the data received up to the
abort is written to the FIFO buffer and an interrupt generated. The processor
then reads the partial byte from the RFDL Data Register and the RDLEOM[x]
output is set high. The processor then reads the RFDL Status Register which will
return a value of logic 1 for the EOM and FLG bits, and set the RDLEOM[x]
相關PDF資料 |
PDF描述 |
|---|---|
| PM6388 | CONNECTOR |
| PM6388-RI | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| PM6541 | E1XC EVALUATION DAUGHTERBOARD |
| PM6650 | MSM6150 CHIPSET SOLUTION |
| PM73121 | AAL1 Segmentation And Reassembly Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PM6344-RI | 制造商:PMC 制造商全稱:PMC 功能描述:QUADRUPLE E1 FRAMER |
| PM6388 | 制造商:PMC 制造商全稱:PMC 功能描述:OCTAL E1 FRAMER |
| PM6388RI | 制造商:PMC-Sierra 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。