參數資料
型號： uPSD3251
廠商： 意法半導體
英文描述： Flash Programmable System Devices with 8032 Microcontroller Core(帶8032微控制器內核的Flash可編程系統設備)
中文描述： 閃存可編程系統設備與8032微控制器內核（帶8032微控制器內核的閃存可編程系統設備）
文件頁數： 108/128頁
文件大?。?/td> 1566K
代理商： UPSD3251
μPSD3251F
108/128
RESET TIMING AND DEVICE STATUS AT RESET
Upon Power-up, the PSD Module requires a Reset
(RESET) pulse of duration t
NLNH-PO
after V
CC
is
steady. During this period, the device loads inter-
nal configurations, clears some of the registers
and sets the Flash memory into operating mode.
After the rising edge of Reset (RESET), the PSD
Module remains in the Reset Mode for an addition-
al period, t
OPR
, before the first memory access is
allowed.
The Flash memory is reset to the READ Mode
upon Power-up. Sector Select (FS0-FS3 and
CSBOOT0-CSBOOT1) must all be Low, WRITE
Strobe (WR, CNTL0) High, during Power-on
RESET for maximum security of the data contents
and to remove the possibility of a byte being writ-
ten on the first edge of WRITE Strobe (WR). Any
Flash memory WRITE cycle initiation is prevented
automatically when V
CC
is below V
LKO
.
Warm RESET
Once the device is up and running, the PSD Mod-
ule can be reset with a pulse of a much shorter du-
ration, t
NLNH
. The same t
OPR
period is needed
before the device is operational after a Warm
RESET. Figure 55 shows the timing of the Power-
up and Warm RESET.
I/O Pin, Register and PLD Status at RESET
Table 80 shows the I/O pin, register and PLD sta-
tus during Power-on RESET, Warm RESET, and
Power-down Mode. PLD outputs are always valid
during Warm RESET, and they are valid in Power-
on RESET once the internal Configuration bits are
loaded. This loading is completed typically long
before the V
CC
ramps up to operating level. Once
the PLD is active, the state of the outputs are de-
termined by the PLD equations.
Figure 55. Reset (RESET) Timing
Table 80. Status During Power-on RESET, Warm RESET and Power-down Mode
Note: 1. The SR_cod and PeriphMode Bits in the VM Register are always cleared to '0' on Power-on RESET or Warm RESET.
Port Configuration
Power-on RESET
Warm RESET
Power-down Mode
MCU I/O
Input mode
Input mode
Unchanged
PLD Output
Valid after internal PSD
configuration bits are
loaded
Valid
Depends on inputs to PLD
(addresses are blocked in
PD Mode)
Address Out
Tri-stated
Tri-stated
Not defined
Register
Power-on RESET
Warm RESET
Power-down Mode
PMMR0 and PMMR2
Cleared to '0'
Unchanged
Unchanged
Macrocells flip-flop status
Cleared to '0' by internal
Power-on RESET
Depends on .re and .pr
equations
Depends on .re and .pr
equations
VM Register
(1)
Initialized, based on the
selection in PSDsoft
Configuration menu
Initialized, based on the
selection in PSDsoft
Configuration menu
Unchanged
All other registers
Cleared to '0'
Cleared to '0'
Unchanged
tNLNH-PO
Power-On Reset
tOPR
AI07437
RESET
tNLNH
Warm Reset
tOPR
V
CC
V
CC
(min)
相關PDF資料
PDF描述
uPSD3253AV-24T1T Flash Programmable System Devices with 8032 Microcontroller Core
UPSD3253B Two and Three Channel Codewheels
UPSD3253BV Flash Programmable System Devices with 8032 Microcontroller Core
uPSD3254B-24T1T Flash Programmable System Devices with 8032 Microcontroller Core
uPSD3254B-40T6T Flash Programmable System Devices with 8032 Microcontroller Core
相關代理商/技術參數
參數描述
uPSD3251MEB 制造商:P&S 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core 制造商:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core
UPSD3253 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core and 256Kbit SRAM
UPSD3253A-24T1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core
UPSD3253A-24T1T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core
UPSD3253A-24T6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*