- 您現在的位置：買賣IC網 > PDF目錄360999 > ISP1761 (NXP Semiconductors N.V.) Hi-Speed Universal Serial Bus On-The-Go controller PDF資料下載
參數資料
| 型號： | ISP1761 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Hi-Speed Universal Serial Bus On-The-Go controller |
| 中文描述： | 高速通用串行總線和On - The - Go控制器 |
| 文件頁數： | 22/158頁 |
| 文件大?。?/td> | 724K |
| 代理商： | ISP1761 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
9397 750 13258
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 12 January 2005
22 of 158
Philips Semiconductors
ISP1761
Hi-Speed USB OTG controller
It is also possible that the system’s DMA will perform a memory-to-memory type of
transfer between the system memory and the ISP1761 memory. The ISP1761 will be
accessed in the PIO mode. Consequently, memory read operations must be preceded by
initializing the Memory register (address 033Ch), as described in
Section 7.3.1
. No IRQ
will be generated by the ISP1761 on completing the DMA transfer but an internal
processor interrupt may be generated to signal that the DMA transfer is completed. This is
mainly useful in implementing the double-buffering scheme for data transfer to optimize
the USB bandwidth.
The ISP1761 DMA programming involves:
Set the active levels of signals DREQ and DACK in the HW Mode Control register.
The DMA Start Address register contains the first memory address at which the data
transfer will start. It must be word-aligned in the 16-bit data bus mode and double
word aligned in the 32-bit data bus mode.
The programming of the HcDMAConfiguration register specifies:
–
The type of transfer that will be performed: read or write.
–
The burst size—expressed in bytes—is specified, regardless of the data bus width.
For the same burst size, a double number of cycles will be generated in the 16-bit
mode data bus width as compared to the 32-bit mode.
–
The transfer length—expressed in number of bytes—defines the number of bursts.
The DREQ will be deasserted and asserted to generate the next burst, as long as
there are bytes to be transferred. At the end of a transfer, the DREQ will be
deasserted and an IRQ can be generated if DMAEOTINT (bit 3 in the HcInterrupt
register) is set. The maximum DMA transfer size is equal to the maximum memory
size. The transfer size can be an odd or even number of bytes, as required. If the
transfer size is an odd number of bytes, the number of bytes transferred by the
system’s DMA is equal to the next multiple of two for the 16-bit data bus width or
four for the 32-bit data bus width. For a write operation, however, only the specified
odd number of bytes in the ISP1761 memory will be affected.
–
Enable ENABLE_DMA (bit 1) of the HcDMAConfiguration register to determine the
assertion of DREQ immediately after setting the bit.
After programming the preceding parameters, the system’s DMA may be enabled (waiting
for the DREQ to start the transfer or immediate transfer may be started).
The programming of the system’s DMA must match the ISP1761 DMA parameters
programmed above. Only one DMA transfer may take place at a time. A PIO mode data
transfer may occur simultaneously with a DMA data transfer, in the same or a different
memory area.
7.4 Interrupts
The ISP1761 will assert the IRQ according to the source or event in the HcInterrupt
register. The main steps to enable the IRQ assertion are:
1. Set GLOBAL_INTR_EN (bit 0) in the HW Mode Control register.
2. Define the IRQ active as level or edge in INTR_LEVEL (bit 1) of the HW Mode Control
register.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1761BE | Hi-Speed Universal Serial Bus On-The-Go controller |
| ISP1761ET | Hi-Speed Universal Serial Bus On-The-Go controller |
| ISP2100A | Telecommunication IC |
| ISP2100BN4 | Microprocessor |
| ISP2300 | Controller Miscellaneous - Datasheet Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1761BE | 功能描述:USB 接口集成電路 USB HS OTG CTRLR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1761BE,518 | 功能描述:USB 接口集成電路 USB HS OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1761BE,551 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -T OR NO "-" RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1761BE,557 | 功能描述:USB 接口集成電路 USB HS OTG CTRLR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1761BE518 | 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB OTG 128LQFP |
發布緊急采購，3分鐘左右您將得到回復。