- 您現在的位置：買賣IC網 > PDF目錄374986 > XC3S1000 (Xilinx, Inc.) Spartan-3 FPGA Family: Complete Data Sheet PDF資料下載
參數資料
| 型號： | XC3S1000 |
| 廠商： | Xilinx, Inc. |
| 英文描述： | Spartan-3 FPGA Family: Complete Data Sheet |
| 中文描述： | 的Spartan - 3 FPGA系列：完整的數據手冊 |
| 文件頁數： | 33/198頁 |
| 文件大小： | 1605K |
| 代理商： | XC3S1000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁
Spartan-3 FPGA Family: Functional Description
26
www.xilinx.com
DS099-2 (v1.3) August 24, 2004
Preliminary Product Specification
40
R
DFS Clock Output Connections
There are two basic cases that determine how to connect
the DFS clock outputs: on-chip and off-chip, which are illus-
trated in
Figure 15a
and
Figure 15c
, respectively. This is
similar to what has already been described for the DLL com-
ponent. See the
DLL Clock Output and Feedback Con-
nections
, page 22
section.
In the on-chip case, it is possible to connect either of the
DFS’s two output clock signals through general routing
resources to the FPGA’s internal registers. Either a Global
Clock Buffer (BUFG) or a BUFGMUX affords access to the
global clock network. The optional feedback loop is formed
in this way, routing CLK0 to a global clock net, which in turn
drives the CLKFB input.
In the off-chip case, the DFS’s two output clock signals, plus
CLK0 for an optional feedback loop, can exit the FPGA
using output buffers (OBUF) to drive a clock network plus
registers on the board. The feedback loop is formed by
feeding the CLK0 signal back into the FPGA using an
IBUFG, which directly accesses the global clock network, or
an IBUF. Then, the global clock net is connected directly to
the CLKFB input.
Phase Shifter (PS)
The DCM provides two approaches to controlling the phase
of a DCM clock output signal relative to the CLKIN signal:
First, there are nine clock outputs that employ the DLL to
achieve a desired phase relationship: CLK0, CLK90,
CLK180, CLK270, CLK2X, CLK2X180, CLKDV CLKFX, and
CLKFX180. These outputs afford “coarse” phase control.
The second approach uses the PS component described in
this section to provide a still finer degree of control. The PS
component accomplishes this by introducing a "fine phase
shift" (T
PS
) between the CLKFB and CLKIN signals inside
the DLL component. The user can control this fine phase
shift down to a resolution of 1/256 of a CLKIN cycle or one
tap delay (DCM_TAP), whichever is greater. When in use,
the PS component shifts the phase of all nine DCM clock
output signals together. If the PS component is used
together with a DCM clock output such as the CLK90,
CLK180, CLK270, CLK2X180 and CLKFX180, then the fine
phase shift of the former gets added to the coarse phase
shift of the latter.
PS Component Enabling and Mode Selection
The CLKOUT_PHASE_SHIFT attribute enables the PS
component for use in addition to selecting between two
operating modes. As described in
Table 16
, this attribute
has three possible values: NONE, FIXED and VARIABLE.
When CLKOUT_PHASE_SHIFT is set to NONE, the PS
component is disabled and its inputs, PSEN, PSCLK, and
PSINCDEC, must be tied to GND. The set of waveforms in
Figure 17a
shows the disabled case, where the DLL main-
tains a zero-phase alignment of signals CLKFB and CLKIN
upon which the PS component has no effect. The PS com-
ponent is enabled by setting the attribute to either the
FIXED or VARIABLE values, which select the Fixed Phase
mode and the Variable Phase mode, respectively. These
two modes are described in the sections that follow
Determining the Fine Phase Shift
The user controls the phase shift of CLKFB relative to
CLKIN by setting and/or adjusting the value of the
PHASE_SHIFT attribute. This value must be an integer
ranging from –255 to +255. The PS component uses this
value to calculate the desired fine phase shift (T
PS
) as a
fraction of the CLKIN period (T
CLKIN
). Given values for
PHASE-SHIFT and T
CLKIN
, it is possible to calculate T
PS
as
follows:
T
PS
= (PHASE_SHIFT/256)*T
CLKIN
Both the Fixed Phase and Variable Phase operating modes
employ this calculation. If the PHASE_SHIFT value is zero,
then CLKFB and CLKIN will be in phase, the same as when
the PS component is disabled. When the PHASE_SHIFT
value is positive, the CLKFB signal will be shifted later in
time with respect to CLKIN. If the attribute value is negative,
the CLKFB signal will be shifted earlier in time with respect
to CLKIN.
(4)
The Fixed Phase Mode
This mode fixes the desired fine phase shift to a fraction of
the T
CLKIN
, as determined by Equation (4) and its
user-selected PHASE_SHIFT value P. The set of wave-
forms in
Figure 17b
illustrates the relationship between
CLKFB and CLKIN in the Fixed Phase mode. In the Fixed
Phase mode, the PSEN, PSCLK and PSINCDEC inputs are
not used and must be tied to GND.
Table 16:
PS Attributes
Attribute
Description
Values
CLKOUT_PHASE_SHIFT
Disables PS component or chooses between Fixed Phase
and Variable Phase modes.
NONE, FIXED, VARIABLE
PHASE_SHIFT
Determines size and direction of initial fine phase shift.
Integers from –255 to +255
(1)
Notes:
1.
The practical range of values will be less when T
> FINE_SHIFT_RANGE in the Fixed Phase mode, also when T
>
(FINE_SHIFT_RANGE)/2 in the Variable Phase mode. the FINE_SHIFT_RANGE represents the sum total delay of all taps.
相關PDF資料 |
PDF描述 |
|---|---|
| XC3S1000-4CP132C | Spartan-3 FPGA Family: Complete Data Sheet |
| XC3S1000-4CP132I | Spartan-3 FPGA Family: Complete Data Sheet |
| XC3S1000-4CPG132C | Spartan-3 FPGA Family: Complete Data Sheet |
| XC3S1000-4CPG132I | Spartan-3 FPGA Family: Complete Data Sheet |
| XC3S1000-4PQ208C | Spartan-3 FPGA Family: Complete Data Sheet |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC3S1000-4CP132C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3 FPGA Family: Complete Data Sheet |
| XC3S1000-4CP132I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3 FPGA |
| XC3S1000-4CPG132C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3 FPGA Family: Complete Data Sheet |
| XC3S1000-4CPG132I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3 FPGA Family: Complete Data Sheet |
| XC3S1000-4FG1156C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-3 FPGA Family : Complete Data Sheet |
發布緊急采購，3分鐘左右您將得到回復。