- 您現在的位置：買賣IC網 > PDF目錄361591 > uPSD3233 (意法半導體) Flash Programmable System Device with 8032 Microcontroller Core(嵌入高速“8032微控制器核”的Flash型可編程系統器) PDF資料下載
參數資料
| 型號： | uPSD3233 |
| 廠商： | 意法半導體 |
| 英文描述： | Flash Programmable System Device with 8032 Microcontroller Core(嵌入高速“8032微控制器核”的Flash型可編程系統器) |
| 中文描述： | 閃存可編程系統器件與8032微控制器內核（嵌入高速“8032微控制器核”的閃存型可編程系統器） |
| 文件頁數： | 19/164頁 |
| 文件大?。?/td> | 1133K |
| 代理商： | UPSD3233 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁
19/164
μ
PSD3200 FAMILY
DRAFT(Thursday 20 June 2002, 13:15).
rotation, the MSB rolls into the LSB position. For a
right rotation, the LSB rolls into the MSB position.
The SWAP A instruction interchanges the high
and low nibbles within the Accumulator. This is a
useful operationin BCD manipulations. For exam-
ple, if the Accumulator contains a binary number
which is known tobeless than 100, itcan be quick-
ly converted to BCD by the following code:
MOVE B,#10
DIV AB
SWAP A
ADD A,B
Dividing the number by 10 leaves the tens digit in
the low nibble of the Accumulator, and the ones
digit in the Bregister. The SWAP and ADDinstruc-
tions move the tens digit to the high nibble of the
Accumulator, and the ones digit to the low nibble.
Table 6. Data Transfer Instructions that Access Internal Data Memory Space
Data Transfers
Internal RAM.
Table 6 shows the menu of in-
structions that are available for moving data
around withinthe internal memory spaces, andthe
addressing modes that can be used with each
one. The MOV <dest>, <src> instruction allows
data to be transferred between any two internal
RAM or SFR locations without going through the
Accumulator. Remember, the Upper 128 bytes of
data RAM can be accessed only by indirect ad-
dressing, and SFR space only by direct address-
ing.
Note that in
μ
PSD3200 Family devices, the stack
resides in on-chip RAM, and grows upwards. The
PUSH instruction first increments the Stack Point-
er (SP), then copies the byte into thestack. PUSH
and POP useonly direct addressing to identify the
byte being savedor restored,but thestack itself is
accessed by indirect addressing using the SP reg-
ister. This means the stack can go into the Upper
128 bytesof RAM, if theyareimplemented, butnot
into SFR space.
The Data Transfer instructions include a 16-bit
MOV thatcan be used to initialize the Data Pointer
(DPTR) for look-up tables in Program Memory.
The XCH A, <byte> instruction causes the Accu-
mulator and ad-dressed byte to exchange data.
The XCHD A, @Ri instruction is similar, but only
the low nibbles are involved in the exchange. To
see how XCH and XCHD can be used to facilitate
data manipulations, consider first the problem of
shifting and 8-digit BCD number two digits to the
right. Table 8 shows how this can be done using
XCH instructions. To aidin understanding how the
code works, the contents of the registers that are
holding the BCD number and the content of the
Accumulator are shown alongside eachinstruction
to indicate their status after the instruction has
been executed.
After the routine hasbeen executed, the Accumu-
lator contains the two digits that were shifted out
on the right. Doing the routine with direct MOVs
uses 14 code bytes. The same operation with
XCHs uses only 9 bytes and executes almost
twice as fast. To right-shift by an odd number of
digits, a one-digit must be executed. Table 9
shows a sample of code that will right-shift a BCD
number one digit, using the XCHD instruction.
Again, the contents of the registers holding the
number and of the accumulator are shown along-
side each instruction.
Mnemonic
Operation
Addressing Modes
Dir.
Ind.
Reg.
Imm
MOV A,<src>
A = <src>
X
X
X
X
MOV <dest>,A
<dest> = A
X
X
X
MOV <dest>,<src>
<dest> = <src>
X
X
X
X
MOV DPTR,#data16
DPTR = 16-bit immediate constant
X
PUSH <src>
INC SP; MOV “@SP”,<src>
X
POP <dest>
MOV <dest>,”@SP”; DEC SP
X
XCH A,<byte>
Exchange contents of A and <byte>
X
X
X
XCHD A,@Ri
Exchange low nibbles of A and @Ri
X
相關PDF資料 |
PDF描述 |
|---|---|
| uPSD3234(中文) | Flash Programmable System Device with 8032 Microcontroller Core(嵌入高速“8032微控制器核”的Flash型可編程系統器) |
| uPSD3212C(中文) | Flash Programmable System Devices with 8032 Microcontroller Core and 16Kbit SRAM(帶8032微控制器內核和16Kbit SRAM的FLASH可編程系統器件) |
| uPSD3254A(中文) | Flash Programmable System Devices with 8032 Microcontroller Core(帶8032微控制器內核的FLASH可編程系統器件) |
| uPSD3254BV(中文) | Flash Programmable System Devices with 8032 Microcontroller Core(帶8032微控制器內核的FLASH可編程系統器件) |
| UPSD3234A | Flash Programmable System Devices with 8032 Microcontroller Core |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPSD3233A-24T1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core |
| UPSD3233A-24T1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core |
| UPSD3233A-24T6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core |
| UPSD3233A-24T6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core |
| UPSD3233A-24U1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core |
發布緊急采購，3分鐘左右您將得到回復。