參數資料
型號： MC68HC916X1CTH16
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PQFP120
封裝： QFP-120
文件頁數： 45/172頁
文件大?。?/td> 1200K
代理商： MC68HC916X1CTH16
MC68HC916X1
MOTOROLA
MC68HC916X1TS/D
139
1.
Turn on VFPE2K (apply program/erase voltage to VFPE2K pin).
2.
Clear ERAS and set LAT and VFPE bits in BFECTL to set program mode, enable program-
ming address and data latches, and invoke special verification read circuitry. Set initial val-
ue of tppulse to tpmin.
3.
Write new data to the desired address. This causes the address and data of the location to
be programmed to be latched in the programming latches.
4.
Set ENPE to apply programming voltage.
5.
Delay long enough for one programming pulse to occur (tppulse).
6.
Clear ENPE to remove programming voltage.
7.
Delay while high voltage is turning off (tvprog).
8.
Read the location just programmed. If the value read is all zeros, proceed to step 9. If not,
calculate a new value for tppulse and repeat steps 4 through 7 until either the location is ver-
ified or the total programming time (tprogmax) has been exceeded. If tprogmax has been ex-
ceeded, the location may be bad and should not be used.
9.
If the location is programmed, calculate tpmargin and repeat steps 4 through 7. If the location
does not remain programmed, the location is bad.
10. Clear VFPE and LAT.
11. If there are more locations to program, repeat steps 2 through 10.
12. Turn off VFPE2K (reduce voltage on VFPE2K pin to VDD).
13. Read the entire array to verify that all locations are correct. If any locations are incorrect,
the array is bad.
10.5.4.2 Erasure Sequence
Use the following procedure to erase the BEFLASH. Refer to Figures 45 and 46 in 11 Electrical
Characteristics for VFPE to VDD relationships during erasure.
1.
Turn on VFPE2K (apply program/erase voltage to VFPE2K pin).
2.
Set initial value of tepulse to temin.
3.
Set LAT, VFPE, and ERAS bits to configure the BEFLASH module for erasure.
4.
Write to any valid address in the control block or array. This allows the erase voltage to be
turned on. The data written and the address written to are of no consequence.
5.
Set ENPE to apply programming voltage.
6.
Delay long enough for one erase pulse to occur (tepulse).
7.
Clear ENPE to remove programming voltage.
8.
Delay while high voltage is turning off (tverase).
9.
Clear LAT, ERAS, and VFPE to allow normal access to the BEFLASH.
10. Read the entire array and control block to ensure that the entire module is erased.
11. If all of the locations are not erased, calculate a new value for tepulse and repeat steps 3
through 10 until either the remaining locations are erased or the maximum erase time
(terasemax) has expired.
12. If all locations are erased, calculate temargin and repeat steps 3 through 10. If all locations
do not remain erased, the BEFLASH module may be bad.
13. Turn off VFPE2K (reduce voltage on VFPE2K pin to VDD).
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC916X1CTH16B1 16-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PQFP120
SPMC916X1CTH16 16-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PQFP120
MC68HCL05J1ADWR2 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20
MC68HC05J1AVDWR2 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20
MC68HCP11A1CFNE3 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC52
相關代理商/技術參數
參數描述
MC68HC98LJ12CFU 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
MC68HC98LJ12CFUE 功能描述:8位微控制器 -MCU 8 BIT MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC9S08RC60 L33R DIE 制造商:Motorola Inc 功能描述:
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*