參數資料
型號： MC68HC916X1CTH16
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PQFP120
封裝： QFP-120
文件頁數： 17/172頁
文件大小： 1200K
代理商： MC68HC916X1CTH16
MC68HC916X1
MOTOROLA
MC68HC916X1TS/D
113
Command RAM is used by the QSPI when in master mode. The CPU writes one byte of control
information to this segment for each QSPI command to be executed. The QSPI cannot modify in-
formation in command RAM.
Command RAM consists of 16 bytes. Each byte is divided into two fields. The peripheral chip-select
field enables peripherals for transfer. The command control field provides transfer options.
A maximum of 16 commands can be in the queue. Queue execution by the QSPI proceeds from
the address in NEWQP[3:0] through the address in ENDQP[3:0]. (Both of these fields are in
SPCR2).
CONT — Continue
0 = Control of chip selects returned to PORTQS after transfer is complete.
1 = Peripheral chip selects remain asserted after transfer is complete.
BITSE — Bits per Transfer Enable
0 = 8 bits
1 = Number of bits set in BITS[3:0] field of SPCR0
DT — Delay after Transfer
The QSPI provides a variable delay at the end of serial transfer to facilitate the interface with peripherals
that have a latency requirement. The delay between transfers is determined by the SPCR1 DTL[6:0]
field.
DSCK — PCS to SCK Delay
0 = PCS valid to SCK transition is one-half SCK.
1 = SPCR1 DSCKL[6:0] field specifies delay from PCS valid to SCK.
PCS[3:0] — Peripheral Chip Select
Use peripheral chip-select bits to select an external device for serial data transfer. More than one pe-
ripheral chip select can be activated at a time, and more than one peripheral chip can be connected to
each PCS pin, provided that proper fanout is observed.
7.4.4 Operating Modes
The QSPI operates in either master or slave mode. Master mode is used when the MCU originates
data transfers. Slave mode is used when an external device initiates serial transfers to the MCU
through the QSPI. Switching between the modes is controlled by MSTR in SPCR0. Before entering
either mode, appropriate QSM and QSPI registers must be properly initialized.
1.
The PCS0 bit represents the dual-function PCS0/SS.
CR[0:F] — Command RAM
$YFFD40
76543210
CONT
BITSE
DT
DSCK
PCS3
PCS2
PCS1
PCS01
––––––––
CONT
BITSE
DT
DSCK
PCS3
PCS2
PCS1
PCS01
COMMAND CONTROL
PERIPHERAL CHIP SELECT
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC916X1CTH16B1 16-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PQFP120
SPMC916X1CTH16 16-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PQFP120
MC68HCL05J1ADWR2 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20
MC68HC05J1AVDWR2 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20
MC68HCP11A1CFNE3 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC52
相關代理商/技術參數
參數描述
MC68HC98LJ12CFU 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
MC68HC98LJ12CFUE 功能描述:8位微控制器 -MCU 8 BIT MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC9S08RC60 L33R DIE 制造商:Motorola Inc 功能描述:
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*