參數資料
型號： MC68HC916X1CTH16
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PQFP120
封裝： QFP-120
文件頁數： 36/172頁
文件大?。?/td> 1200K
代理商： MC68HC916X1CTH16
MOTOROLA
MC68HC916X1
130
MC68HC916X1TS/D
10. If the location is programmed, repeat the same number of pulses as required to program
the location. This provides 100% program margin.
11. Read the address to verify that it remains programmed.
12. Clear the LAT bit in FEExCTL. This disables the programming address and data latches.
13. If more locations are to be programmed, repeat steps 2 through 10.
14. Reduce voltage applied to the VFPE pin to normal read level.
9.6.4.2 Erasure
The following steps are used to erase a flash EEPROM array. Figure 23 is a flowchart of the era-
sure operation. Refer to Figures 45 and 46 in 11 Electrical Characteristics for VFPE to VDD rela-
tionships during erasure.
1.
Increase voltage applied to the VFPE pin to program/erase/verify level.
2.
Set the ERAS bit and the LAT bit in FEExCTL. This configures the module for erasure.
3.
Perform a write to any valid address in the control block or array. The data written does not
matter.
4.
Set the ENPE bit in FEExCTL. This applies the erase voltage to the array.
5.
Delay the proper amount of time for one erase pulse. Delay is specified by parameter tepk.
6.
Clear the ENPE bit in FEExCTL. This turns off erase voltage to the array.
7.
Delay while high voltage to array is turned off. Delay is specified by parameter ter.
8.
Read the entire array and control block to ensure all locations are erased.
9.
If all locations are not erased, calculate a new value for tepk (tei × pulse number) and repeat
steps 3 through 10 until all locations erase, or the maximum number of pulses has been
applied.
10. If all locations are erased, calculate the erase margin (em) and repeat steps 3 through 10
for the single margin pulse.
11. Clear the LAT and ERAS bits in FEExCTL. This allows normal access to the flash.
12. Reduce voltage applied to the VFPE pin to normal read level.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC916X1CTH16B1 16-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PQFP120
SPMC916X1CTH16 16-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PQFP120
MC68HCL05J1ADWR2 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20
MC68HC05J1AVDWR2 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20
MC68HCP11A1CFNE3 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC52
相關代理商/技術參數
參數描述
MC68HC98LJ12CFU 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
MC68HC98LJ12CFUE 功能描述:8位微控制器 -MCU 8 BIT MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC9S08RC60 L33R DIE 制造商:Motorola Inc 功能描述:
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*