參數資料
型號: MC68HC05G3
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PQFP80
封裝: QFP-80
文件頁數: 102/128頁
文件大小: 290K
代理商: MC68HC05G3
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁當前第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
Page 65
Section 7: SERIAL PERIPHERAL INTERFACE (SPI)
MOTOROLA
MC68HC05G3 (705G4) Specification Rev. 1.1
SECTION 7
SERIAL PERIPHERAL INTERFACE (SPI)
Two serial peripheral interfaces (SPI) are built into the MC68HC05G3 (705G4).
In the SPI format, three separate wires are required for data input, output, and clock. In this
format, the clock is not being included in the data stream and must be provided as a
separate signal. The three pins are occupied for serial clock, input data, and output data.
When one of the SPIs is enabled (SPE = 1), bit 0 through bit 2 of port C/port G become
SDI, SDO, and SCK pins, and the corresponding DDRC/DDRG bit has no affect on the
direction of the pin.
The MSTR bit decides the SPI operation mode; SCK pin is configured as output in the
master mode and configured as input in the slave mode.
The DORD bit in the serial peripheral control register (SPCR) selects the data transmission
order. When DORD bit is set, the LSB of serial data is shifted out/in first. When the DORD
bit is clear, serial data is shifted from MSB.
Serial clock speed is selectable by the SPR bit in the SPCR. Interrupt may be generated
by the completion of transfer.
7.1
FEATURES
Full Duplex, Three-Wire Synchronous Transfers
Master and Slave Operation
Programmable Data Transmission Order
E/2 (Maximum) Master Bit Frequency
E (Maximum) Slave Bit Frequency
Two Programmable Master Bit Rates
End of Transmission Interrupt Flag
Wakeup from Stop Mode (Slave Mode Only)
7.2
FUNCTIONAL DESCRIPTIONS
A block diagram of the serial peripheral is shown in Figure 7-2.
The clock start logic is triggered by CPU (detection of CPU write to the 8-bit shift register
(SPDR)) and originates the system clock (SCK) based on the internal processor clock. This
clock also is used in the 3-bit counter and 8-bit shift register.
After data is written to the 8-bit shift register of the master device, it is then shifted out to
the SDO pin for application to the slave device. At the same time, data applied from a slave
device via the SDI pin is shifted into the 8-bit shift register.
相關PDF資料
PDF描述
MC68HC705J5ACJP 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP16
MC68HC705J5ACP 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP20
MC68HC05J5AJDW 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO16
MC68HRC705J5ACDW 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO20
MC68HRC05J5ADW 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20
相關代理商/技術參數
參數描述
MC68HC05J1 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS MICROCONTROLLER UNIT
MC68HC05J1A 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers
MC68HC05J1ACDW 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers
MC68HC05J1ACP 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers
MC68HC05J1ADW 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers