- 您現在的位置：買賣IC網 > PDF目錄1976 > XRT72L71IQ (Exar Corporation)IC FRAMER DS3 ATM UNI 160PQFP PDF資料下載
參數資料
| 型號： | XRT72L71IQ |
| 廠商： | Exar Corporation |
| 文件頁數： | 81/102頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FRAMER DS3 ATM UNI 160PQFP |
| 產品變化通告： | XRT72Lx Series Obsolescence 02/May/2012 |
| 標準包裝： | 24 |
| 控制器類型： | DS3 ATM UNI，透明通道調幀器 |
| 電源電壓： | 3.3V |
| 電流 - 電源： | 120mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 160-BQFP |
| 供應商設備封裝： | 160-PQFP（28x28） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
XRT72L71
á
DS3 ATM UNI/CLEAR CHANNEL FRAMER
REV. 1.1.0
4
PIN DESCRIPTIONS (SEE FIGURE 3)
PIN DESCRIPTION
PIN NO.
SYMBOL
TYPE
DESCRIPTION
1D15
I/O
MSB of Bi-Directional Data Bus (Microprocessor Interface Section): This
pin, along with pins D0 - D14, function as the Microprocessor Interface bi-direc-
tional data bus, and is intended to be interfaced to the “l(fā)ocal” microprocessor.
This pin is inactive if the Microprocessor Interface block is configured to oper-
ate over an 8 bit data bus.
2TAOS
O
“Transmit All Ones Signal” (TAOS) Command (for the XRT7300 LIU IC).
This output pin is intended to be connected to the TAOS input pin of the XR-
T7300 LIU IC. The user can control the state of this output pin by writing a ‘0’
or ‘1’ to Bit 4 (TAOS) within the Line Interface Drive Register (Address = 0x72).
If the user commands this signal to toggle "High" then it will force the
XRT7300 DS3 Line Transmitter IC to transmit an "All Ones" pattern onto the
line. Conversely, if the user commands this output signal to toggle "Low" then
the XRT7300 DS3 Line Transmitter IC will proceed to transmit data based upon
the pattern that it receives via the TxPOS and TxNEG output pins.
Writing a "1" to Bit 4 of the Line Interface Drive Register (Address = 0x72) will
cause this output pin to toggle "High". Writing a "0" to this bit-field will cause
this output pin to toggle "Low".
NOTE: If the designer is not using the XRT7300 DS3/E3/STS-1 LIU IC, then
this output pin can be used for other purposes.
3
4
5
D14
D13
D12
I/O
Bi-directional Data bus (Microprocessor Interface Section): This pin is
inactive if the Microprocessor Interface block is configured to operate over an
8 bit data bus. Please see description for D15, pin 1.
6DMO
I
“Drive Monitor Output” Input (from the XRT7300 LIU IC): This input pin is
intended to be tied to the DMO output pin of the XRT7300 E3/DS3/STS-1 LIU
IC. The user can determine the state of this input pin by reading Bit 2 (DMO)
within the Line Interface Scan Register (Address = 0x73). If this input signal is
“High”, then it means that the drive monitor circuitry (within the XRT7300 LIU
IC) has not detected any bipolar signals at the MTIP and MRING inputs within
the last 128 ± 32 bit-periods. If this input signal is “Low”, then it means that
bipolar signals are being detected at the MTIP and MRING input pins of the
XRT7300.
NOTE: If the designer is not using the XRT7300 E3/DS3/STS-1 LIU IC, then
this input pin can be used for other purposes.
7MOTO/Intel
I
Motorola/Intel Processor Interface Select Mode: This input pin allows the
user to configure the Microprocessor Interface to interface with either a “Motor-
ola-type” or “Intel-type” microprocessor/microcontroller. Tying this input pin to
VDD, configures the microprocessor interface to operate in the Motorola mode
(e.g., the UNI/Framer can be readily interfaced to a “Motorola type” local
microprocessor). Tying this input pin to GND configures the microprocessor
interface to operate in the Intel Mode (e.g., the UNI/Framer can be readily inter-
faced to an “Intel type” local microprocessor).
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73L02MIV-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| XRT73L03BIV-F | IC LIU E3/DS3/STS-1 3CH 120LQFP |
| XRT73L04BIV-F | IC LIU E3/DS3/STS-1 4CH 144LQFP |
| XRT73L06IB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT73LC00AIV-F | IC LIU STS1/DS3/E3 SGL 44TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT72L71IQ-F | 功能描述:網絡控制器與處理器 IC Single CH DS3 UNI (3.3V) RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT72L73IB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XRT72L74IB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XRT7300 | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT7300ES | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。