- 您現在的位置：買賣IC網 > PDF目錄98050 > P95020NQG8 (INTEGRATED DEVICE TECHNOLOGY INC) 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132 PDF資料下載
參數資料
| 型號： | P95020NQG8 |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132 |
| 封裝： | 10 X 10 MM, 0.85 MM HEIGHT, QFN-132 |
| 文件頁數： | 11/169頁 |
| 文件大?。?/td> | 4297K |
| 代理商： | P95020NQG8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁
IDTP95020
Product Datasheet
September 2, 2011 Revision 1.3 Final
108
2011 Integrated Device Technology, Inc.
Table 168 – Register 0xA089 (0x89) Peak Current Limit (I_LIM) Settings Bits [3:2]
BIT 3 BIT 2 DESCRIPTION
0
Peak Current Limit = 25 %
0
1
Peak Current Limit = 50 %
1
0
Peak Current Limit = 75 %
1
Peak Current Limit = 100 % A
Note: Peak Current Limit is maximum when bits [3:2] are both set to 1.
Boost5 – Enable / Disable
There are two methods of disabling the BOOST5 Converter: the Global Enable bit and the local ENABLE bit. Table 169
shows the interoperation of the two methods.
Table 169. Interoperability of Enabling / Disabling Methods vs. Loading Default Values
INTERNAL
POR
GLOBAL
ENABLE
ON/OFF
STATUS
REGISTER VALUE STATUS
0
X
0
OFF
PREVIOUS SETTINGS
0
X
OFF
PREVIOUS SETTINGS
0
1
ON
PREVIOUS SETTINGS
1
X
OFF
LOAD DEFAULT VALUES
Initialization and Device Power-up
During an IC re-initialization or “cold boot”, an internal
POR disables the BOOST5 Converter and loads the
default values into the registers. The default values are
only loaded into the registers when there is a POR event.
The default settings for the Output Voltage Register are:
Table 170. Boost5 Output Voltage Register Default
FUNCTION
DEFAULT SETTING
Local Enable Bit
Disabled
Output Voltage
5.0V
Table 171. Boost5 Control Register Default
FUNCTION
DEFAULT SETTING
Current Limit
100%
Clock Frequency
1 MHz
After the POR releases, the Global Enable bit can be set
to HIGH. Since the default value of the local ENABLE bit
is LOW, the supply will not start at this time.
To enable the BOOST5 converter, the local ENABLE bit is
set to HIGH by writing a “1” to the Output Voltage Register.
The Output Voltage value must be included each time the
converter is enabled or disabled. The default value for the
converter is read and written back along with the ENABLE
bit or a different voltage can be written. When the
ENABLE bit becomes set the BOOST5 Converter enters
its soft-start sequence, ending up at the programmed
voltage.
NOTE: Changes to the Output Voltage Register settings
can be written directly without disabling the converter.
Normal Disabling / Enabling
Setting either the Global Enable bit to LOW or the local
ENABLE bit to LOW will turn off the BOOST5 Converter.
The Global Enable bit’s sole purpose is to shut down the
converter into its lowest power shutdown mode. It is not
intended to be used to toggle the BOOST5 Converter off
and on. Proper operation is only guaranteed by toggling
the ENABLE bit HIGH once the Global Enable bit is set
HIGH to take it out of low power shutdown mode.
Startup and Soft-Start
There is a direct path from VIN through the external
inductor (L) into the BOOST5_SWn pins, through SR1 to
the BOOST5_OUT pin which directly charges the output
capacitor (COUT) to ~VIN. During startup the converter
continues charging to the programmed Output Voltage
using Soft-Start. During the Soft Start sequence the
BOOST5 limits the peak inductor current for the first
500s.
相關PDF資料 |
PDF描述 |
|---|---|
| P95020ZNQGI8 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132 |
| P95020ZLLG | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA124 |
| P95020ZLLGI | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA124 |
| P95020ZNQGI | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132 |
| P95020ZNQG | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P95020ZDLLG | 制造商:Integrated Device Technology Inc 功能描述:124-LGA - Bulk |
| P95020ZDLLG8 | 制造商:Integrated Device Technology Inc 功能描述:124-LGA - Tape and Reel |
| P95020ZDNQG | 制造商:Integrated Device Technology Inc 功能描述:132-VFQFPN - Bulk |
| P95020ZDNQG8 | 制造商:Integrated Device Technology Inc 功能描述:132-VFQFPN - Tape and Reel |
| P95021NQG | 功能描述:PMIC 解決方案 Integrates Audio, LED B/Light Pwr Mgt RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。