參數資料
型號: ISP1761BE
廠商: NXP SEMICONDUCTORS
元件分類: 總線控制器
英文描述: Hi-Speed Universal Serial Bus On-The-Go controller
中文描述: UNIVERSAL SERIAL BUS CONTROLLER, PQFP128
封裝: 14 X 20 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT425-1, LQFP-128
文件頁數: 85/158頁
文件大?。?/td> 724K
代理商: ISP1761BE
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
9397 750 13258
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 12 January 2005
85 of 158
Philips Semiconductors
ISP1761
Hi-Speed USB OTG controller
peripheral, and the A-device assumes the role of a host. The A-device detects that the
B-device can support HNP by getting the OTG descriptor from the B-device. The A-device
will then enable the HNP hand-off by using SetFeature (b_hnp_enable) and then go into
the suspend state. The B-device signals claiming the host role by deasserting its pull-up
resistor. The A-device acknowledges by going into the peripheral state. The B-device then
assumes the role of a host and communicates with the A-device as long as it wishes.
When the B-device finishes communicating with the A-device, both the devices finally go
into the idle state. See
Figure 15
and
Figure 16
.
9.3 Session Request Protocol (SRP)
As a dual-role device, the ISP1761 can initiate and respond to SRP. The B-device initiates
SRP by data line pulsing, followed by V
BUS
pulsing. The A-device can detect either data
line pulsing or V
BUS
pulsing.
9.3.1
B-device initiating SRP
The ISP1761 can initiate SRP by performing the following steps:
1. Detect initial conditions [read B_SESS_END and B_SE0_SRP (bits 7 and 8) of the
OTG Status register].
2. Start data line pulsing [set DP_PULLUP (bit 0) of the OTG Control (set) register to
logic 1].
3. Wait for 5 ms to 10 ms.
4. Stop data line pulsing [set DP_PULLUP (bit 0) of the OTG Control (clear) register to
logic 0].
5. Start V
BUS
pulsing [set VBUS_CHRG (bit 6) of the OTG Control (set) register to
logic 1].
6. Wait for 10 ms to 20 ms.
7. Stop V
BUS
pulsing [set VBUS_CHRG (bit 6) of the OTG Control (clear) register to
logic 0].
8. Discharge V
BUS
for about 30 ms [by using VBUS_DISCHRG (bit 5) of the OTG
Control (set) register], optional.
The B-device must complete both data line pulsing and V
BUS
pulsing within 100 ms.
9.3.2
A-device responding to SRP
The A-device must be able to respond to one of the two SRP events: data line pulsing or
V
BUS
pulsing. When data line pulsing is used, the ISP1761 can detect DP pulsing. This
means that the peripheral-only device must initiate data line pulsing through DP. A
dual-role device will always initiate data line pulsing through DP.
To enable the SRP detection through the V
BUS
pulsing, set A_B_SESS_VLD (bit 1) in the
OTG Interrupt Enable Fall and OTG Interrupt Enable Rise registers.
To enable the SRP detection through the DP pulsing, set DP_SRP (bit 2) in the OTG
Interrupt Enable Rise register.
相關PDF資料
PDF描述
ISP1761ET Hi-Speed Universal Serial Bus On-The-Go controller
ISP2100A Telecommunication IC
ISP2100BN4 Microprocessor
ISP2300 Controller Miscellaneous - Datasheet Reference
ISP2310 Controller Miscellaneous - Datasheet Reference
相關代理商/技術參數
參數描述
ISP1761BE,518 功能描述:USB 接口集成電路 USB HS OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1761BE,551 功能描述:USB 接口集成電路 DO NOT USE ORDER -T OR NO "-" RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1761BE,557 功能描述:USB 接口集成電路 USB HS OTG CTRLR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1761BE518 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB OTG 128LQFP
ISP1761BEGE 功能描述:IC USB CTRL HI-SPEED 128LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A