參數資料
型號: M80C286
廠商: Intel Corp.
英文描述: High Performance CHMOS Microprocessor With Memory Management And Protection(帶存儲管理和保護高性能16位CHMOS微處理器)
中文描述: 高性能CHMOS微處理器存儲器管理和保護(帶存儲管理和保護高性能16位CHMOS微處理器)
文件頁數: 9/60頁
文件大小: 957K
代理商: M80C286
M80C286
SINGLE STEP INTERRUPT
The M80C286 has an internal interrupt that allows
programs to execute one instruction at a time. It is
called the single step interrupt and is controlled by
the single step flag bit (TF) in the flag word. Once
this bit is set, an internal single step interrupt will
occur after the next instruction has been executed.
The interrupt clears the TF bit and uses an internally
supplied vector of 1. The IRET instruction is used to
set the TF bit and transfer control to the next instruc-
tion to be single stepped.
Interrupt Priorities
When simultaneous interrupt requests occur, they
are processed in a fixed order as shown in Table 5.
Interrupt processing involves saving the flags, return
address, and setting CS:IP to point at the first in-
struction of the interrupt handler. If other interrupts
remain enabled they are processed before the first
instruction of the current interrupt handler is execut-
ed. The last interrupt processed is therefore the first
one serviced.
Table 5. Interrupt Processing Order
Order
Interrupt
1
Instruction exception
2
Single step
3
NMI
4
Processor extension segment overrun
5
INTR
6
INT instruction
Initialization and Processor Reset
Processor initialization or start up is accomplished
by driving the RESET input pin HIGH. RESET forces
the M80C286 to terminate all execution and local
bus activity. No instruction or bus activity will occur
as long as RESET is active. After RESET becomes
inactive and an internal processing interval elapses,
the M80C286 begins execution in real address
mode with the instruction at physical location
FFFFF0(H). RESET also sets some registers to pre-
defined values as shown in Table 6.
Table6.M80C286InitialRegisterStateafterRESET
Flag word
Machine Status Word
Instruction pointer
Code segment
Data segment
Extra segment
Stack segment
0002(H)
FFF0(H)
FFF0(H)
F000(H)
0000(H)
0000(H)
0000(H)
HOLD must not be active during the time from the
leading edge of RESET to 34 CLKs after the trailing
edge of RESET.
Machine Status Word Description
The machine status word (MSW) records when a
task switch takes place and controls the operating
mode of the M80C286. It is a 16-bit register of which
the lower four bits are used. One bit places the CPU
into protected mode, while the other three bits, as
shown in Table 7, control the processor extension
interface.
After
RESET,
FFF0(H) which places the M80C286 in M8086 real
address mode.
this
register
contains
Table 7. MSW Bit Functions
Bit
Name
Function
Position
0
PE
Protected mode enable places the
M80C286 into protected mode and
cannot be cleared except by RESET.
1
MP
Monitor processor extension allows
WAIT instructions to cause a processor
extension not present exception
(number 7).
2
EM
Emulate processor extension causes a
processor extension not present
exception (number 7) on ESC
instructions to allow emulating a
processor extension.
3
TS
Task switched indicates the next
instruction using a processor extension
will cause exception 7, allowing software
to test whether the current processor
extension context belongs to the current
task.
The LMSW and SMSW instructions can load and
store the MSW in real address mode. The recom-
mended use of TS, EM, and MP is shown in Table 8.
Table 8. Recommended MSW Encodings For Processor Extension Control
Instructions
Causing
Exception 7
TS
MP
EM
Recommended Use
0
0
0
Initial encoding after RESET. M80C286 operation is identical to M8086, 88.
None
0
0
1
No processor extension is available. Software will emulate its function.
ESC
1
0
1
No processor extension is available. Software will emulate its function. The current
processor extension context may belong to another task.
ESC
0
1
0
A processor extension exists.
None
1
1
0
A processor extension exists. The current processor extension context may belong to
another task. The Exception 7 on WAIT allows software to test for an error pending
from a previous processor extension operation.
ESC or
WAIT
9
相關PDF資料
PDF描述
M80C287 80-Bit CHMOS III Numeric Processor Exetension(80位CHMOS III數字處理器擴展)
M80C51FB CHMOS Single-Chip 8-Bit Microcontroller(CHMOS單芯片8位微控制器)
M80C86 CHMOS 16-Bit Microcontroller(16位CHMOS 微處理器)
M80C86-20 CHMOS 16-Bit Microcontroller(16位CHMOS 微處理器)
M80C86-2 16-BIT CHMOS MICROPROCESSOR
相關代理商/技術參數
參數描述
M80C287 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:80-BIT CHMOS III NUMERIC PROCESSOR EXTENSION
M80C31BH 制造商:ROCHESTER 制造商全稱:ROCHESTER 功能描述:CMOS SINGLE - CHIP 8-BIT MICROCOMPUTER 64K program Memory Space
M80C31F 制造商:OK International 功能描述:
M80C31FV-1 制造商:OKI Semiconductor 功能描述:8-BIT, 16 MHZ, MICROCONTROLLER, PQFP44
M80C39H 制造商:OK International 功能描述:Electronic Component