- 您現在的位置：買賣IC網 > PDF目錄359054 > M34571G4 (Renesas Technology Corp.) SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M34571G4 |
| 廠商： | Renesas Technology Corp. |
| 英文描述： | SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片4位微機的CMOS |
| 文件頁數： | 61/126頁 |
| 文件大?。?/td> | 1627K |
| 代理商： | M34571G4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁
Rev.1.02
REJ03B0179-0102
May 25, 2007
Page 61 of 124
4571 Group
4. Oscillator concerns
Take care to prevent an oscillator that generates clocks for a
microcomputer operation from being affected by other signals.
(1) Keeping oscillator away from large current signal lines
Install a microcomputer (and especially an oscillator) as far as
possible from signal lines where a current larger than the
tolerance of current value flows.
<Reason>
In the system using a microcomputer, there are signal lines for
controlling motors, LEDs, and thermal heads or others. When a
large current flows through those signal lines, strong noise
occurs because of mutual inductance.
(2) Installing oscillator away from signal lines where potential
levels change frequently
Install an oscillator and a connecting pattern of an oscillator
away from signal lines where potential levels change frequently.
Also, do not cross such signal lines over the clock lines or the
signal lines which are sensitive to noise.
<Reason>
Signal lines where potential levels change frequently (such as the
CNTR pin signal line) may affect other lines at signal rising edge
or falling edge. If such lines cross over a clock line, clock
waveforms may be deformed, which causes a microcomputer
failure or a program runaway.
Fig 67. Wiring for a large current signal line
Fig 68. Wiring to a signal line where potential levels
change frequently
(3) Oscillator protection using V
SS
pattern
As for a two-sided printed circuit board, print a V
SS
pattern on
the underside (soldering side) of the position (on the component
side) where an oscillator is mounted.
Connect the V
SS
pattern to the microcomputer V
SS
pin with the
shortest possible wiring. Besides, separate this V
SS
pattern from
other V
SS
patterns.
Fig 69. Vss pattern on the underside of an oscillator
5. Setup for I/O ports
Setup I/O ports using hardware and software as follows:
<Hardware>
Connect a resistor of 100
or more to an I/O port in series.
<Software>
As for an input port, read data several times by a program for
checking whether input levels are equal or not.
As for an output port or an I/O port, since the output data may
reverse because of noise, rewrite data to its port latch at fixed
periods.
Rewrite data to pull-up control registers at fixed periods.
6. Providing of watchdog timer function by software
If a microcomputer runs away because of noise or others, it can
be detected by a software watchdog timer and the microcomputer
can be reset to normal operation. This is equal to or more
effective than program runaway detection by a hardware
watchdog timer. The following shows an example of a watchdog
timer provided by software. In the following example, to reset a
microcomputer to normal operation, the main routine detects
errors of the interrupt processing routine and the interrupt
processing routine detects errors of the main routine.
This example assumes that interrupt processing is repeated
multiple times in a single main routine processing.
X
IN
X
OUT
V
SS
M
Microcomputer
Mutual inductance
Large
current
GND
X
IN
X
OUT
V
SS
CNTR
Do not cross
N.G.
Oscillator wiring
pattern example
An example of V
SS
patterns on the
underside of a printed circuit board
Separate the V
SS
line for oscillation from other V
SS
lines
X
IN
X
OUT
V
SS
相關PDF資料 |
PDF描述 |
|---|---|
| M3488Q1 | 256 x 256 DIGITAL SWITCHING MATRIX |
| M3488 | 256 x 256 DIGITAL SWITCHING MATRIX |
| M3488B1 | 256 x 256 DIGITAL SWITCHING MATRIX |
| M3493B2 | CMOS 12 X 8 CROSSPOINTWITH CONTROL MEMORY |
| M3493B1 | CMOS 12 X 8 CROSSPOINTWITH CONTROL MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34571G4FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34571G4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34571G6 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34571G6FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34571G6-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發(fā)布緊急采購，3分鐘左右您將得到回復。