參數資料
型號： M34571G4
廠商： Renesas Technology Corp.
英文描述： SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
中文描述： 單芯片4位微機的CMOS
文件頁數： 37/126頁
文件大?。?/td> 1627K
代理商： M34571G4
Rev.1.02
REJ03B0179-0102
May 25, 2007
Page 37 of 124
4571 Group
WATCHDOG TIMER
Watchdog timer provides a method to reset the system when a
program run-away occurs. Watchdog timer consists of timer
WDT(16-bit binary counter), watchdog timer enable flag (WEF),
and watchdog timer flags (WDF1, WDF2).
The timer WDT downcounts the instruction clocks as the count
source from “FFFF
16
” after system is released from reset.
After the count is started, when the timer WDT underflow occurs
(after the count value of timer WDT reaches “0000
16
,” the next
count pulse is input), the WDF1 flag is set to “1.” If the WRST
instruction is never executed until the timer WDT underflow
occurs (until timer WDT counts 65534), WDF2 flag is set to “1,”
and the RESET pin outputs “L” level to reset the microcomputer.
Execute the WRST instruction at each period of 65534 machine
cycle or less by software when using watchdog timer to keep the
microcomputer operating normally.
When the WEF flag is set to “1” after system is released from
reset, the watchdog timer function is valid.
When the DWDT instruction and the WRST instruction are
executed continuously, the WEF flag is cleared to “0” and the
watchdog timer function is invalid.
The WEF flag is initialized to “1” at system reset or RAM back-
up mode.
The WRST instruction has the skip function. When the WRST
instruction is executed while the WDF1 flag is “1”, the WDF1
flag is cleared to “0” and the next instruction is skipped.
When the WRST instruction is executed while the WDF1 flag is
“0”, the next instruction is not skipped.
The skip function of the WRST instruction can be used even
when the watchdog timer function is invalid.
Fig 37. Watchdog timer function
(1) Reset released
65534 count
(Note)
(4)
(2)
(2)
(3) WRST instruction
executed (skip executed)
(5) System reset
FFFF
16
0000
16
Value of 16-bit timer (WDT)
WDF1 flag
WDF2 flag
RESET pin output
(1) After system is released from reset (= after program is started), timer WDT starts count down.
(2) When timer WDT underflow occurs, WDF1 flag is set to “1”.
(3) When the WRST instruction is executed while the WDF1 flag is “1”, WDF1 flag is cleared to “0”, the next
instruction is skipped.
(4) When timer WDT underflow occurs while WDF1 flag is “1”, WDF2 flag is set to “1” and the watchdog reset
signal is output.
(5) The output transistor of RESET pin is turned “ON” by the watchdog reset signal and system reset is
executed.
Note: The number of count is equal to the number of machine cycle because the count source of watchdog timer
is the instruction clock.
相關PDF資料
PDF描述
M3488Q1 256 x 256 DIGITAL SWITCHING MATRIX
M3488 256 x 256 DIGITAL SWITCHING MATRIX
M3488B1 256 x 256 DIGITAL SWITCHING MATRIX
M3493B2 CMOS 12 X 8 CROSSPOINTWITH CONTROL MEMORY
M3493B1 CMOS 12 X 8 CROSSPOINTWITH CONTROL MEMORY
相關代理商/技術參數
參數描述
M34571G4FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34571G4-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34571G6 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34571G6FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34571G6-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*