- 您現在的位置：買賣IC網 > PDF目錄377000 > DSP1628 TVS 400W 60V BIDIRECT SMA PDF資料下載
參數資料
| 型號： | DSP1628 |
| 英文描述： | TVS 400W 60V BIDIRECT SMA |
| 中文描述： | 澄清，串行I /設備的DSP1620/27/28/29 O控制注冊說明 |
| 文件頁數： | 19/114頁 |
| 文件大小： | 804K |
| 代理商： | DSP1628 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
Preliminary Data Sheet
February 1997
DSP1628 Digital Signal Processor
Lucent Technologies Inc.
17
A trap has four cycles of latency. At most, two instruc-
tions will execute from the time the trap is received at
the pin to when it gains control. An instruction that is ex-
ecuting when a trap occurs is allowed to complete be-
fore the trap service routine is entered. (Note that the
instruction could be lengthened by wait-states.) During
normal program execution, the
pi
register contains ei-
ther the address of the next instruction (two-cycle in-
struction executing) or the address following the next
instruction (one-cycle instruction executing). In an inter-
rupt service routine,
pi
contains the interrupt return ad-
dress. When a trap occurs during an interrupt service
routine, the value of the
pi
register may be overwritten.
Specifically, it is not possible to return to an interrupt
service routine from a user trap (0x46) service routine.
Continuing program execution when a trap occurs dur-
ing a cache loop is also not possible.
The HDS trap causes circuitry to force the program
memory map to MAP1 (with on-chip ROM starting at ad-
dress 0x0) when the trap is taken. The previous memo-
ry map is restored when the trap service routine exits by
issuing an ireturn. The map is forced to MAP1 because
the HDS code, if present, resides in the on-chip ROM.
Using the Lucent Technologies development tools, the
TRAP pin may be configured to be an output, or an input
vectoring to address 0x3. In a multiprocessor environ-
ment, the TRAP pins of all the DSPs present can be tied
together. During HDS operations, one DSP is selected
by the host software to be the master. The master pro-
cessor's TRAP pin is configured to be an output.
The TRAP pins of the slave processors are configured
as inputs. When the master processor reaches a break-
point, the master's TRAP pin is asserted. The slave pro-
cessors will respond to their TRAP input by beginning to
execute the HDS code.
AWAIT Interrupt (Standby or Sleep Mode)
Setting the AWAIT bit (bit 15) of the
alf
register
(
alf
= 0x8000) causes the processor to go into a power-
saving standby or sleep mode. Only the minimum cir-
cuitry on the chip required to process an incoming inter-
rupt remains active. After the AWAIT bit is set, one
additional instruction will be executed before the stand-
by power-saving mode is entered. A PHIF or SIO word
transfer will complete if already in progress. The AWAIT
bit is reset when the first interrupt occurs. The chip then
wakes up and continues executing.
Two
nop
instructions should be programmed after the
AWAIT bit is set. The first
nop
(one cycle) will be exe-
cuted before sleeping; the second will be executed after
the interrupt signal awakens the DSP and before the in-
terrupt service routine is executed.
4 Hardware Architecture
(continued)
* Traps due to HDS breakpoints have no effect on VEC[3:0] pins.
Table 4. Interrupt Vector Table
Source
Vector
—
0x2
0x1
0x42
0x4
0x10
0x14
0x18
0x1c
0x20
0x24
0x2c
0x30
0x34
0x38
0x3
0x46
Priority
—
1
2
3
4
7
8
9
10
11
12
14
15
16
17
18
19 = highest
VEC[3:0]
0x0
0x1
0x2
0x8
0x9
0xc
0xd
0xe
0x0
0x1
0x2
0x3
0x4
0x5
0x6
*
0x7
Issued by
—
icall
pin
jtag in
pin
timer
SIO2 in
SIO2 out
—
ECCP ready
ECCP overflow
SIO in
SIO out
PHIF in
PHIF out
breakpoint, jtag, or pin
pin
No Interrupt
Software Interrupt
INT0
JINT
INT1
TIME
IBF2
OBE2
Reserved
EREADY
EOVF
IBF
OBE
PIBF
POBE
TRAP from HDS
TRAP from User
相關PDF資料 |
PDF描述 |
|---|---|
| DSP16210 | TVS 400W 6.5V UNIDIRECT SMA |
| DSP1627 | TVS 400W 6.5V BIDIRECT SMA |
| DSP1629 | TVS 400W 64V UNIDIRECT SMA |
| DSP16410C | TVS 400W 7.0V UNIDIRECT SMA |
| DSP16410 | 16-bit fixed point DSP with Flash |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSP1629 | 制造商:AGERE 制造商全稱:AGERE 功能描述:DSP1629 Digital Signal Processor |
| DSP1629BA10K10IT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP|16-BIT|CMOS|BGA|144PIN|PLASTIC |
| DSP1629BA10K12.5IR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital Signal Processor |
| DSP1629BA10K16.7IT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP|16-BIT|CMOS|BGA|144PIN|PLASTIC |
| DSP1629BA10K19.2IR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。