參數資料
型號： 16F872
廠商： Microchip Technology Inc.
英文描述： CAT 5E CROSSOVER PATCH CORD CABLE GREEN 10 FT
中文描述： 28引腳，8位閃存微控制器的CMOS
文件頁數： 64/160頁
文件大?。?/td> 2600K
代理商： 16F872
PIC16F872
DS30221A-page 64
Preliminary
1999 Microchip Technology Inc.
FIGURE 9-7:
I
2
C WAVEFORMS FOR TRANSMISSION (7-BIT ADDRESS)
9.2.2
GENERAL CALL ADDRESS SUPPORT
The addressing procedure for the I
2
C bus is such that
the first byte after the START condition usually deter-
mines which device will be the slave addressed by the
master. The exception is the general call address,
which can address all devices. When this address is
used, all devices should, in theory, respond with an
acknowledge.
The general call address is one of eight addresses
reserved for specific purposes by the I
2
C protocol. It
consists of all 0’s with R/W = 0
The general call address is recognized when the Gen-
eral Call Enable bit (GCEN) is enabled (SSPCON2<7>
is set). Following a start-bit detect, 8 bits are shifted
into SSPSR and the address is compared against
SSPADD. It is also compared to the general call
address and fixed in hardware.
If the general call address matches, the SSPSR is
transferred to the SSPBUF, the BF flag is set (eighth
bit), and on the falling edge of the ninth bit (ACK bit), the
SSPIF flag is set.
When the interrupt is serviced, the source for the inter-
rupt can be checked by reading the contents of the
SSPBUF to determine if the address was device spe-
cific or a general call address.
In 10-bit mode, the SSPADD is required to be updated
for the second half of the address to match, and the UA
bit is set (SSPSTAT<1>). If the general call address is
sampled when GCEN is set while the slave is config-
ured in 10-bit address mode, then the second half of
the address is not necessary, the UA bit will not be set,
and the slave will begin receiving data after the
acknowledge (
Figure 9-8
).
FIGURE 9-8:
SLAVE MODE GENERAL CALL ADDRESS SEQUENCE (7 OR 10-BIT MODE)
SDA
SCL
SSPIF
BF (SSPSTAT<0>)
CKP (SSPCON<4>)
A7
A6
A5
A4
A3
A2
A1
ACK
D7
D6
D5
D4
D3
D2
D1
D0
Not ACK
Transmitting Data
R/W = 1
Receiving Address
1
Data in
sampled
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
P
cleared in software
SSPBUF is written in software
From SSP interrupt
service routine
Set bit after writing to SSPBUF
(the SSPBUF must be written-to
before the CKP bit can be set)
S
SCL held low
rewhile CPU
R/W = 0
SDA
SCL
S
SSPIF
BF
(SSPSTAT<0>)
SSPOV
(SSPCON<6>)
Cleared in software
SSPBUF is read
R/W = 0
ACK
General Call Address
Address is compared to General Call Address
after ACK, set interrupt flag
GCEN
(SSPCON2<7>)
Receiving data
ACK
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
D7
D6
D5
D4
D3
D2
D1
D0
’0’
’1’
相關PDF資料
PDF描述
16F876A 28/40-pin Enhanced FLASH Microcontrollers
16F876 CAT 5E CROSSOVER, GREEN 15 FT PATCH CABLE
16F877 CAT 5E CROSSOVER PATCH CORD CABLE GREEN 20 FT
16FL100S02 6A, 12A AND 16A FAST RECOVERY RECTIFIERS
16FL100S05 6A, 12A AND 16A FAST RECOVERY RECTIFIERS
相關代理商/技術參數
參數描述
16F876 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin 8-Bit CMOS FLASH Microcontrollers
16F876A 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin Enhanced FLASH Microcontrollers
16F877 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin 8-Bit CMOS FLASH Microcontrollers
16F9040 制造商:未知廠家 制造商全稱:未知廠家 功能描述:COMPACT DIGITALMULTIMETER TRUE RMS
16F9041 制造商:未知廠家 制造商全稱:未知廠家 功能描述:COMPACT DMM MIT RS232
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*