參數資料
型號: S29GL128N10TAIV13
廠商: SPANSION LLC
元件分類: PROM
英文描述: 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
中文描述: 8M X 16 FLASH 3V PROM, 100 ns, PDSO56
封裝: MO-142BEC, TSOP-56
文件頁數: 64/100頁
文件大小: 952K
代理商: S29GL128N10TAIV13
62
S29GL-N MirrorBit Flash Family
S29GL-N_00_B3 October 13, 2006
D a t a S h e e t
Volatile Sector Protection Command Set
The Volatile Sector Protection Command Set permits the user to set the Dynamic Protection
Bit (DYB) to the
protected state
, clear the Dynamic Protection Bit (DYB) to the
unprotected
state
, and read the logic state of the Dynamic Protection Bit (DYB).
The
Volatile Sector Protection Command Set Entry
command sequence must be issued
prior to any of the commands listed following to enable proper command execution.
Note that issuing the
Volatile Sector Protection Command Set Entry
command
disables
reads and w rites from main memory
.
DYB Set Command
DYB Clear Command
The DYB Set and DYB Clear commands are used to protect or unprotect a given sector. The
high order address bits are issued at the same time as the code 00h or 01h on DQ7-DQ0. All
other DQ data bus pins are ignored during the data write cycle. The DYB bits are modifiable
at any time, regardless of the state of the PPB bit or PPB Lock Bit. The DYB bits are cleared
to the
unprotected state
at power-up or hardware reset.
DYB Status Read Command
The programming state of the DYB bit for a given sector can be verified by writing a DYB Sta-
tus Read command to the device. This requires an initial access delay.
The
Volatile Sector Protection Command Set Exit
command must be issued after the ex-
ecution of the commands listed previously to reset the device to read mode.
Note that issuing the
Volatile Sector Protection Command Set Exit command re-en-
ables reads and w rites to the main memory
.
Secured Silicon Sector Entry Command
The Secured Silicon Sector Entry command allows the following commands to be executed
Read from Secured Silicon Sector
Program to Secured Silicon Sector
Once the Secured Silicon Sector Entry Command is issued, the Secured Silicon Sector Exit
command has to be issued to exit Secured Silicon Sector Mode.
Secured Silicon Sector Exit Command
The Secured Silicon Sector Exit command may be issued to exit the Secured Silicon Sector
Mode.
相關PDF資料
PDF描述
S29GL128N10TAIV20 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10TAIV22 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10TAIV23 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10TFI010 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10TFI012 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
相關代理商/技術參數
參數描述
S29GL128N10TF101 制造商:Spansion 功能描述:
S29GL128N10TFI010 功能描述:IC FLASH 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:128Mb (16M x 8,8M x 16) 寫周期時間 - 字,頁:100ns 訪問時間:100ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C(TA) 安裝類型:表面貼裝 封裝/外殼:56-TFSOP(0.724",18.40mm 寬) 供應商器件封裝:56-TSOP 標準包裝:91
S29GL128N10TFI020 制造商:Spansion 功能描述:S29GL128N10TFI020 制造商:Spansion 功能描述:Flash - NOR IC
S29GL128N11FAI020 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 128M-Bit 16M x 8/8M x 16 110ns 64-Pin Fortified BGA Tray
S29GL128N11FAI023 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 128M-Bit 16M x 8/8M x 16 110ns 64-Pin Fortified BGA T/R