- 您現在的位置：買賣IC網 > PDF目錄365394 > S29GL128N10TAIV13 (SPANSION LLC) 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology PDF資料下載
參數資料
| 型號： | S29GL128N10TAIV13 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
| 中文描述： | 8M X 16 FLASH 3V PROM, 100 ns, PDSO56 |
| 封裝： | MO-142BEC, TSOP-56 |
| 文件頁數： | 53/100頁 |
| 文件大?。?/td> | 952K |
| 代理商： | S29GL128N10TAIV13 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
S29GL-N_00_B3 October 13, 2006
S29GL-N MirrorBit Flash Family
51
D a t a S h e e t
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manufacturer and
device codes, and determine whether or not a sector is protected.
Table 12 on page 63
and
Table 14 on page 65
show the address and data requirements. This method is an alternative
to that shown in
Table 5 on page 37
, which is intended for PROM programmers and requires
V
ID
on address pin A9. The autoselect command sequence may be written to an address that
is either in the read or erase-suspend-read mode. The autoselect command may not be writ-
ten while the device is actively programming or erasing.
The autoselect command sequence is initiated by first writing two unlock cycles. This is fol-
lowed by a third write cycle that contains the autoselect command. The device then enters
the autoselect mode. The system may read at any address any number of times without ini-
tiating another autoselect command sequence:
A read cycle at address XX00h returns the manufacturer code.
Three read cycles at addresses 01h, 0Eh, and 0Fh return the device code.
A read cycle to an address containing a sector address (SA), and the address 02h on A7–
A0 in word mode returns 01h if the sector is protected, or 00h if it is unprotected.
The system must write the reset command to return to the read mode (or erase-sus-
pend-read mode if the device was previously in Erase Suspend).
Enter Secured Silicon Sector/ Exit Secured Silicon
Sector Command Sequence
The Secured Silicon Sector region provides a secured data area containing an 8-word/16-byte
random Electronic Serial Number (ESN). The system can access the Secured Silicon Sector
region by issuing the three-cycle Enter Secured Silicon Sector command sequence. The de-
vice continues to access the Secured Silicon Sector region until the system issues the
four-cycle Exit Secured Silicon Sector command sequence. The Exit Secured Silicon Sector
command sequence returns the device to normal operation.
Table 12 on page 63
shows the
address and data requirements for both command sequences. See also “Secured Silicon Sec-
tor Flash Memory Region” for further information.
Note that the ACC function and unlock
bypass modes are not available when the Secured Silicon Sector is enabled.
W ord Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is initiated by
writing two unlock write cycles, followed by the program set-up command. The program ad-
dress and data are written next, which in turn initiate the Embedded Program algorithm. The
system is
not
required to provide further controls or timings. The device automatically pro-
vides internally generated program pulses and verifies the programmed cell margin.
Table 12
on page 63
and
Table 14 on page 65
show the address and data requirements for the word
program command sequence.
When the Embedded Program algorithm is complete, the device then returns to the read
mode and addresses are no longer latched. The system can determine the status of the pro-
gram operation by using DQ7 or DQ6. Refer to the Write Operation Status section for
information on these status bits.
Any commands written to the device during the Embedded Program Algorithm are ignored.
Note that the Secured Silicon Sector, autoselect, and CFI functions are unavailable
w hen a program operation is in progress.
Note that a
hardw are reset
immediately ter-
minates the program operation. The program command sequence should be reinitiated once
the device has returned to the read mode, to ensure data integrity.
Programming is allowed in any sequence of address locations and across sector boundaries.
Programming to the same word address multiple times without intervening erases (incremen-
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL128N10TAIV20 | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
| S29GL128N10TAIV22 | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
| S29GL128N10TAIV23 | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
| S29GL128N10TFI010 | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
| S29GL128N10TFI012 | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL128N10TF101 | 制造商:Spansion 功能描述: |
| S29GL128N10TFI010 | 功能描述:IC FLASH 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:128Mb （16M x 8，8M x 16） 寫周期時間 - 字，頁:100ns 訪問時間:100ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.724"，18.40mm 寬） 供應商器件封裝:56-TSOP 標準包裝:91 |
| S29GL128N10TFI020 | 制造商:Spansion 功能描述:S29GL128N10TFI020 制造商:Spansion 功能描述:Flash - NOR IC |
| S29GL128N11FAI020 | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 128M-Bit 16M x 8/8M x 16 110ns 64-Pin Fortified BGA Tray |
| S29GL128N11FAI023 | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 128M-Bit 16M x 8/8M x 16 110ns 64-Pin Fortified BGA T/R |
發布緊急采購，3分鐘左右您將得到回復。