參數資料
型號： P95020NQG
廠商： INTEGRATED DEVICE TECHNOLOGY INC
元件分類： 電源管理
英文描述： 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132
封裝： 10 X 10 MM, 0.85 MM HEIGHT, QFN-132
文件頁數： 23/169頁
文件大小： 4297K
代理商： P95020NQG
IDTP95020
Product Datasheet
September 2, 2011 Revision 1.3 Final
119
2011 Integrated Device Technology, Inc.
General Purpose ADC Mode
In this mode, GPIO6/7/8/9 are analog general purpose
auxiliary signal inputs ADC1/ADC3/ADC2/ADC0. There
are also four other internal signals connect to the ADC
input multiplexer: BAT, TEMP, VSYS and ICHRG. These
signals are for battery voltage, die temperature, system
voltage and charging current measurement. To achieve
data coherency when result registers are read, use the I2C
burst mode to read the entire result.
ADC Auto Power Down Mode
In this mode, the ADC and internal reference are usually
off. When a measurement is either scheduled by the
internal timer or an external request, the device powers up
the ADC and internal reference, and then waits for the
internal reference to settle. After settling, the signal
acquisition starts. The ADC and the reference will be
powered
down
after
all
the
outstanding
scheduled/requested tasks are finished. All the
measurement channels are accessed in a round-robin
manner.
ADC Always On Mode
In this mode, the ADC is always powered up and the
internal ADC reference is always on. The internal
reference remains fully powered after completing a
sequence. All the measurement channels are accessed in
a round-robin manner.
System Monitoring and Alert Generation
There are four internal channels that support scheduled
measurement and monitoring:
-
Battery voltage (VBAT) measurement
-
Die Temperature (VTEMP) measurement
-
Vsys Level (VSYS) measurement
-
Battery charging current (CHRG_ICHRG)
measurement
Among those, three of them include alert signal generation:
-
Battery voltage
-
Die temperature
-
Vsys level
Measured results are saved in dedicated result registers
and compared with pre-defined spec limits. If the result is
out of the limit, an alert (map to processor interrupt) signal
can be asserted and alert status will be set.
ADC and TSC Module – Registers
PCON Register- ADC_TSC Enable Register
IC Address = Page-0: 39(0x39), C Address = 0xA039
Table 180. PCON Register- ADC_TSC Enable Register
BIT
BIT NAME
DEFAULT
SETTING
USER
TYPE
VALUE
DESCRIPTION / COMMENTS
0
ADC_TSC_EN 0b
RW
0 = Disabled
1 = Enabled
Enable ADC or Touch screen controller. When disabled,
the ADC_TSC module retains the configuration register
settings but the clock is gated (low power mode).
[7:1] RESERVED
0000000b
RW
RESERVED
相關PDF資料
PDF描述
P95020NQG8 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132
P95020ZNQGI8 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132
P95020ZLLG 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA124
P95020ZLLGI 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA124
P95020ZNQGI 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC132
相關代理商/技術參數
參數描述
P95020NQG8 制造商:Integrated Device Technology Inc 功能描述:Power Management and Control 132-Pin QFN EP T/R 制造商:Integrated Device Technology Inc 功能描述:POWER MANAGEMENT AUDIO & CONTROL - Tape and Reel 制造商:Integrated Device Technology Inc 功能描述:Integrates Audio, LED B/Light Pwr Mgt
P95020ZDLLG 制造商:Integrated Device Technology Inc 功能描述:124-LGA - Bulk
P95020ZDLLG8 制造商:Integrated Device Technology Inc 功能描述:124-LGA - Tape and Reel
P95020ZDNQG 制造商:Integrated Device Technology Inc 功能描述:132-VFQFPN - Bulk
P95020ZDNQG8 制造商:Integrated Device Technology Inc 功能描述:132-VFQFPN - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*