參數資料
型號： CY7C67200
廠商： Cypress Semiconductor Corp.
英文描述： EZ-OTG Programmable USB On-The-Go Host/Peripheral Controller(EZ-OTG可編程USB On-The-Go主機/外圍設備控制器)
中文描述： 的EZ - OTG公司可編程的USB On - The - Go的主機/外設控制器（的EZ - OTG公司可編程的USB On - The - Go的主機/外圍設備控制器）
文件頁數： 38/82頁
文件大小： 1719K
代理商： CY7C67200
CY7C67200
Document #: 38-08014 Rev. *F
Page 38 of 82
SOF/EOP Interrupt Flag
(Bit 9)
The SOF/EOP Interrupt Flag bit indicates if the SOF/EOP
received interrupt has triggered.
1:
Interrupt triggered
0:
Interrupt did not trigger
Reset Interrupt Flag
(Bit 8)
The Reset Interrupt Flag bit indicates if the USB Reset
Detected interrupt has triggered.
1:
Interrupt triggered
0:
Interrupt did not trigger
EP7 Interrupt Flag
(Bit 7)
The EP7 Interrupt Flag bit indicates if the endpoint seven
(EP7) Transaction Done interrupt has triggered. An EPx
Transaction Done interrupt triggers when any of the following
responses or events occur in a transaction for the devices
given EP: send/receive ACK, send STALL, Time-out occurs,
IN Exception Error, or OUT Exception Error. In addition, if the
NAK Interrupt Enable bit in the Device n Endpoint Control
register is set, this interrupt also triggers when the device
NAKs host requests.
1:
Interrupt triggered
0:
Interrupt did not trigger
EP6 Interrupt Flag
(Bit 6)
The EP6 Interrupt Flag bit indicates if the endpoint six (EP6)
Transaction Done interrupt has triggered. An EPx Transaction
Done interrupt triggers when any of the following responses or
events occur in a transaction for the devices given EP:
send/receive ACK, send STALL, Time-out occurs, IN
Exception Error, or OUT Exception Error. In addition, if the
NAK Interrupt Enable bit in the Device n Endpoint Control
register is set, this interrupt also triggers when the device
NAKs host requests.
1:
Interrupt triggered
0:
Interrupt did not trigger
EP5 Interrupt Flag
(Bit 5)
The EP5 Interrupt Flag bit indicates if the endpoint five (EP5)
Transaction Done interrupt has triggered. An EPx Transaction
Done interrupt triggers when any of the following responses or
events occur in a transaction for the devices given EP:
send/receive ACK, send STALL, Time-out occurs, IN
Exception Error, or OUT Exception Error. In addition, if the
NAK Interrupt Enable bit in the Device n Endpoint Control
register is set, this interrupt also triggers when the device
NAKs host requests.
1:
Interrupt triggered
0:
Interrupt did not trigger
EP4 Interrupt Flag
(Bit 4)
The EP4 Interrupt Flag bit indicates if the endpoint four (EP4)
Transaction Done interrupt has triggered. An EPx Transaction
Done interrupt triggers when any of the following responses or
events occur in a transaction for the devices given EP:
send/receive ACK, send STALL, Time-out occurs, IN
Exception Error, or OUT Exception Error. In addition, if the
NAK Interrupt Enable bit in the Device n Endpoint Control
register is set, this interrupt also triggers when the device
NAKs host requests.
1:
Interrupt triggered
0:
Interrupt did not trigger
EP3 Interrupt Flag
(Bit 3)
The EP3 Interrupt Flag bit indicates if the endpoint three (EP3)
Transaction Done interrupt has triggered. An EPx Transaction
Done interrupt triggers when any of the following responses or
events occur in a transaction for the devices given EP:
send/receive ACK, send STALL, Time-out occurs, IN
Exception Error, or OUT Exception Error. In addition, if the
NAK Interrupt Enable bit in the Device n Endpoint Control
register is set, this interrupt also triggers when the device
NAKs host requests.
1:
Interrupt triggered
0:
Interrupt did not trigger
EP2 Interrupt Flag
(Bit 2)
The EP2 Interrupt Flag bit indicates if the endpoint two (EP2)
Transaction Done interrupt has triggered. An EPx Transaction
Done interrupt triggers when any of the following responses or
events occur in a transaction for the devices given EP:
send/receive ACK, send STALL, Time-out occurs, IN
Exception Error, or OUT Exception Error. In addition, if the
NAK Interrupt Enable bit in the Device n Endpoint Control
register is set, this interrupt also triggers when the device
NAKs host requests.
1:
Interrupt triggered
0:
Interrupt did not trigger
EP1 Interrupt Flag
(Bit 1)
The EP1 Interrupt Flag bit indicates if the endpoint one (EP1)
Transaction Done interrupt has triggered. An EPx Transaction
Done interrupt triggers when any of the following responses or
events occur in a transaction for the devices given EP:
send/receive ACK, send STALL, Time-out occurs, IN
Exception Error, or OUT Exception Error. In addition, if the
NAK Interrupt Enable bit in the Device n Endpoint Control
register is set, this interrupt also triggers when the device
NAKs host requests.
1:
Interrupt triggered
0:
Interrupt did not trigger
EP0 Interrupt Flag
(Bit 0)
The EP0 Interrupt Flag bit indicates if the endpoint zero (EP0)
Transaction Done interrupt has triggered. An EPx Transaction
Done interrupt triggers when any of the following responses or
events occur in a transaction for the devices given EP:
send/receive ACK, send STALL, Time-out occurs, IN
Exception Error, or OUT Exception Error. In addition, if the
NAK Interrupt Enable bit in the Device n Endpoint Control
register is set, this interrupt also triggers when the device
NAKs host requests.
1:
Interrupt triggered
0:
Interrupt did not trigger
Reserved
All reserved bits must be written as ‘0’.
相關PDF資料
PDF描述
CY7C68320C EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
CY7C68301C EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
CY7C68300C EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
CY7C68321C EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
CY8C20434 PSoC Mixed-Signal Array(PSoC混合信號陣列)
相關代理商/技術參數
參數描述
CY7C672001-48BAXI 功能描述:8位微控制器 -MCU CY7C672001-48BAXI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
CY7C672001-48BAXIT 功能描述:8位微控制器 -MCU CY7C672001-48BAXIT RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
CY7C67200-48BAXI 功能描述:USB 接口集成電路 LO PWR OTG IND RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C67200-48BAXIT 功能描述:USB 接口集成電路 LO PWR OTG IND RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C67300-100AI 制造商:Cypress Semiconductor 功能描述:INTERFACE MISC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*