- 您現在的位置：買賣IC網 > PDF目錄385949 > TSB81BA3I (Texas Instruments, Inc.) IEEE 1394b THREE-PORT CABLE TRANSCEIVER/ARBITER PDF資料下載
參數資料
| 型號： | TSB81BA3I |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | IEEE 1394b THREE-PORT CABLE TRANSCEIVER/ARBITER |
| 中文描述： | 的IEEE 1394b三端口電纜收發器/仲裁者 |
| 文件頁數： | 18/57頁 |
| 文件大?。?/td> | 810K |
| 代理商： | TSB81BA3I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
SLLS559B DECEMBER 2002 REVISED OCTOBER 2003
18
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
Table 4. Page 0 (Port Status) Register Field Descriptions
FIELD
SIZE
TYPE
DESCRIPTION
Astat
2
Rd
TPA line state. This field indicates the instantaneous TPA line state of the selected port, encoded
as follows:
Code
Arb Value
11
Z
01
1
10
0
00
invalid
Bstat
2
Rd
TPB line state. This field indicates the TPB line state of the selected port. This field has the same
encoding as the AStat field.
Ch
1
Rd
Child/parent status. A 1 indicates that the selected port is a child port. A 0 indicates that the selected
port is the parent port. A disconnected, disabled, or suspended port is reported as a child port. The
Ch bit is invalid after a bus-reset until tree-ID has completed.
Con
1
Rd
Debounced port connection status. This bit indicates that the selected port is connected. The
connection must be stable for the debounce time of approximately 341 ms for the Con bit to be set
to 1. The Con bit is reset to 0 by hardware reset and is unaffected by bus-reset.
NOTE: The Con bit indicates that the port is physically connected to a peer PHY, but this does not
mean that the port is necessarily active. For 1394b-coupled connections, the Con bit is set when a
port detects connection tones from the peer PHY and operating speed negotiation is completed.
RxOK
1
Rd
Receive OK. In 1394a2000 mode this bit indicates the reception of a debounced TPBias signal.
In Beta_mode, this bit indicates the reception of a continuous electrically valid signal.
Note: RxOK is set to false during the time that only connection
tones
are detected in beta mode.
Dis
1
Rd/Wr
Port disabled control. If this bit is 1, then the selected port is disabled. The Dis bit is reset to 0 by
hardware reset (all ports are enabled for normal operation following hardware reset). The Dis bit is
not affected by bus-reset. When this bit is set, the port cannot become active; however, the port still
tones, but does not establish an active connection.
Negotiated_speed
3
Rd
Indicates the maximum speed negotiated between this PHY port and its immediately connected port.
The encoding is as for Max_port_speed. It is set on connection when in Beta_mode, or to a value
established during self-ID when in 1394a2000 mode.
PIE
1
Rd/Wr
Port event interrupt enable. When this bit is 1, a port event on the selected port sets the port event
interrupt (PEI) bit and notifies the link. This bit is reset to 0 by a hardware reset, and is unaffected
by bus-reset.
Fault
1
Rd/Wr
Fault. This bit indicates that a resume-fault or suspend-fault has occurred on the selected port, and
that the port is in the suspended state. A resume-fault occurs when a resuming port fails to detect
incoming cable bias from its attached peer. A suspend-fault occurs when a suspending port
continues to detect incoming cable bias from its attached peer. Writing 1 to this bit clears the Fault
bit to 0. This bit is reset to 0 by hardware reset and is unaffected by bus-reset.
Standby_fault
1
Rd/Wr
This bit is set to 1 if an error is detected during a standby operation and cleared on exit from the
standby state. A write of 1 to this bit or receipt of the appropriate remote command packet clears it
to 0. When this bit is cleared, standby errors are cleared.
Disscrm
1
Rd/Wr
Disable scrambler. If this bit is set to 1, then the data sent during packet transmission is not
scrambled.
B_Only
1
Rd
Beta-mode operation only. For the TSB81BA3, this bit is set to 0 for all ports.
DC_connected
1
Rd
If this bit is set to 1, the port has detected a dc connection to the peer port by means of a 1394a-style
connect detect circuit.
相關PDF資料 |
PDF描述 |
|---|---|
| TSE-0155-32S-P1-3 | SINGLE MODE SINGLE FIBER TRANSCEIVER |
| TSL230 | PROGRAMMABLE LIGHT-TO-FREQUENCY CONVERTERS |
| TSL235(中文) | Programmable Light-To-Frequency Converter(光頻轉換器) |
| TSL245(中文) | IR Light-To-Frequency Converter(紅外光頻轉換器) |
| TSL250(中文) | Light-To-Voltage Converter(光壓轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSB81BA3IPFP | 功能描述:射頻收發器 s800 3-Port Cable Xcvr/Arbiter RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| TSB81BA3IPFPEP | 功能描述:射頻收發器 Mil Enh 3-Port Cable Xcvr/Arbiter RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| TSB81BA3PFP | 功能描述:射頻收發器 s800 3-Port Cable Xcvr/Arbiter RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| TSB81BA3PFPG4 | 功能描述:射頻收發器 s800 3-Port Cable Xcvr/Arbiter RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| TSB82AA2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1394b OHCI-LYNX CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。