- 您現在的位置：買賣IC網 > PDF目錄380717 > ST72774S9T1 (意法半導體) 8-BIT USB MCU FOR MONITORS, WITH UP TO 60K OTP, 1K RAM, ADC, TIMER, SYNC, TMU, PWM/BRM, H/W DDC & I2C PDF資料下載
參數資料
| 型號： | ST72774S9T1 |
| 廠商： | 意法半導體 |
| 元件分類： | ADC |
| 英文描述： | 8-BIT USB MCU FOR MONITORS, WITH UP TO 60K OTP, 1K RAM, ADC, TIMER, SYNC, TMU, PWM/BRM, H/W DDC & I2C |
| 中文描述： | 8位USB單片機的顯示器，高達60K章檢察官辦公室，每1000內存，模數轉換器，定時器，同步，材質單元，脈寬調制/的BRM，的H / W DDC的 |
| 文件頁數： | 111/144頁 |
| 文件大?。?/td> | 1280K |
| 代理商： | ST72774S9T1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁當前第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁
ST72774/ST727754/ST72734
111/144
DDC INTERFACE
(Cont’d)
DDC STATUS REGISTER 1 (SR1)
Read Only
Reset Value: 0000 0000 (00h)
Bit 7 =
EVF
Event flag.
This bit is set by hardware as soon as an event
occurs. It is cleared by software reading SR2
register in case of error event or as described in
Figure 67
. It is also cleared by hardware when the
interface is disabled (PE=0).
0: No event
1: One of the following events has occurred:
– BTF=1 (Byte received or transmitted)
– ADSL=1 (Address matched in Slave mode
while ACK=1)
– AF=1 (No acknowledge received after byte
transmission if ACK=1)
– STOPF=1 (Stop condition detected in Slave
mode)
– BERR=1 (Bus error, misplaced Start or Stop
condition detected)
Bit 6 = Reserved. Forced to 0 by hardware.
Bit 5 =
TRA
Transmitter/Receiver.
When BTF is set, TRA=1 if a data byte has been
transmitted. It is cleared automatically when BTF
is cleared. It is also cleared by hardware after
detection of Stop condition (STOPF=1) or when
the interface is disabled (PE=0).
0: Data byte received (if BTF=1)
1: Data byte transmitted
Bit 4 =
BUSY
Bus busy
.
This bit is set by hardware on detection of a Start
condition and cleared by hardware on detection of
a Stop condition. It indicates a communication in
progress on the bus. This information is still
updated when the interface is disabled (PE=0).
0: No communication on the bus
1: Communication ongoing on the bus
Bit 3 =
BTF
Byte transfer finished.
This bit is set by hardware as soon as a byte is
correctly received or transmitted with interrupt
generation if ITE=1. It is cleared by software
reading SR1 register followed by a read or write of
DR register. It is also cleared by hardware when
the interface is disabled (PE=0).
– Following a byte transmission, this bit is set after
reception of the acknowledge clock pulse. . BTF
is cleared by reading SR1 register followed by
writing the next byte in DR register.
– Following a byte reception, this bit is set after
transmission of the acknowledge clock pulse if
ACK=1. BTF is cleared by reading SR1 register
followed by reading the byte from DR register.
The SCL line is held low while BTF=1.
0: Byte transfer not done
1: Byte transfer succeeded
Bit 2 =
ADSL
Address matched (Slave mode).
This
bit is set by hardware as soon as the received
slave address matched with the OAR register
content or the Enhanced DDC address is
recognized. An interrupt is generated if ITE=1. It is
cleared by software reading SR1 register or by
hardware when the interface is disabled (PE=0).
The SCL line is held low while ADSL=1.
0: Address mismatched or not received
1: Received address matched
Bit 1:0 = Reserved. Forced to 0 by hardware.
7
0
EVF
0
TRA
BUSY
BTF
ADSL
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| ST72E734J6D0 | 8-BIT USB MCU FOR MONITORS, WITH UP TO 60K OTP, 1K RAM, ADC, TIMER, SYNC, TMU, PWM/BRM, H/W DDC & I2C |
| ST727T272N5B1 | 8-BIT MCU WITH 24K ROM, EEPROM,ADC,PWM/BRM DACs,SYNC PROCESSOR,EWPCC,TIMER AND DDC INTERFACE |
| ST727E272N5D1 | 8-BIT MCU WITH 24K ROM, EEPROM,ADC,PWM/BRM DACs,SYNC PROCESSOR,EWPCC,TIMER AND DDC INTERFACE |
| ST7272 | 8-BIT MCU WITH 24K ROM, EEPROM,ADC,PWM/BRM DACs,SYNC PROCESSOR,EWPCC,TIMER AND DDC INTERFACE |
| ST7272N5B1 | 8-BIT MCU WITH 24K ROM, EEPROM,ADC,PWM/BRM DACs,SYNC PROCESSOR,EWPCC,TIMER AND DDC INTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST727X4-EMU2B | 制造商:STMicroelectronics 功能描述:REALTIME EMULATOR BOARD - Bulk |
| ST727X4-EPB/US | 制造商:STMicroelectronics 功能描述:PROGRAMMER - Bulk |
| ST-7-28 | 功能描述:XFRMR PWR 115V 14VAC 2.6A RoHS:是 類別:變壓器 >> 功率 系列:ST 標準包裝:1 系列:260 類型:標準 最大功率:65 VA 主線圈:雙 副線圈:三路，中心抽頭 在某電流時的串聯輸出電壓:500 VAC @ 85mA，5 VAC @ 2A，6.3 VAC @ 2A 在某電流時的并聯輸出電壓:- 安裝類型:底座安裝 尺寸/尺寸:102.36mm L x 67.31mm W 高度 - 座高（最大）:66.80mm 端接類型:導線引線 |
| ST7-28 | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:POWER TRANSFORMER |
| ST7-28B56 | 功能描述:電源變壓器 SPLIT BOBBIN HORZ MOUNT XFMR RoHS:否 制造商:Triad Magnetics 功率額定值:12 VA 初級電壓額定值:115 V / 230 V 次級電壓額定值:12 V / 24 V 安裝風格:SMD/SMT 一次繞組:Dual Primary Winding 二次繞組:Dual Secondary Winding 長度:2.5 in 寬度:2 in 高度:1.062 in |
發布緊急采購，3分鐘左右您將得到回復。