4
–
32
4.45 Power Management Capabilities Register
The power management capabilities register contains information on the capabilities of the PC Card function related
to power management. Both PCI1620 CardBus bridge functions support D0, D1, D2, and D3 power states. Default
register value is FE12h for operation in accordance with
PCI Bus Power Management Interface Specification
revision
1.1. See Table 4
–
18 for a complete description of the register contents.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Power management capabilities
Type
RW
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
1
1
1
1
1
1
1
0
0
0
0
1
0
0
1
0
Register:
Offset:
Type:
Default:
Power management capabilities
A2h (Functions 0, 1)
Read-only, Read/Write
FE12h
Table 4
–
18. Power Management Capabilities Register Description
BIT
SIGNAL
TYPE
FUNCTION
This 5-bit field indicates the power states from which the PCI1620 device functions can assert PME. A 0
for any bit indicates that the function cannot assert the PME signal while in that power state. These 5 bits
return 11111b when read. Each of these bits is described below:
15
PME support
RW
Bit 15
–
defaults to a 1 indicating the PME signal can be asserted from the D3cold state. This bit is read/write
because wake-up support from D3cold is contingent on the system providing an auxiliary power source
to the VCC terminals. If the system designer chooses not to provide an auxiliary power source to the VCC
terminals for D3cold wake-up support, then BIOS should write a 0 to this bit.
Bit 14
–
contains the value 1 to indicate that the PME signal can be asserted from the D3hot state.
Bit 13
–
contains the value 1 to indicate that the PME signal can be asserted from the D2 state.
Bit 12
–
contains the value 1 to indicate that the PME signal can be asserted from the D1 state.
Bit 11
–
contains the value 1 to indicate that the PME signal can be asserted from the D0 state.
This bit returns a 1 when read, indicating that the function supports the D2 device power state.
14
–
11
R
10
D2_Support
R
9
D1_Support
R
This bit returns a 1 when read, indicating that the function supports the D1 device power state.
8
–
6
RSVD
R
Reserved. These bits return 000b when read.
5
DSI
R
Device-specific initialization. This bit returns 0 when read.
4
AUX_PWR
R
Auxiliary power source. This bit is meaningful only if bit 15 (D3cold supporting PME) is set. When this bit
is set, it indicates that support for PME in D3cold requires auxiliary power supplied by the system by way
of a proprietary delivery vehicle.
A 0 (zero) in this bit field indicates that the function supplies its own auxiliary power source.
If the function does not support PME while in the D3cold state (bit 15=0), then this field must always return
0.
3
PMECLK
R
When this bit is 1, it indicates that the function relies on the presence of the PCI clock for PME operation.
When this bit is 0, it indicates that no PCI clock is required for the function to generate PME.
Functions that do not support PME generation in any state must return 0 for this field.
2
–
0
Version
R
These 3 bits return 010b when read, indicating that there are 4 bytes of general-purpose power
management (PM) registers as described in draft revision 1.1 of the
PCI Bus Power Management Interface
Specification
.
This is a PME context bit and can be cleared only by the assertion of GRST when PME is enabled. If PME is not enabled, then this bit is cleared
by the assertion of PRST or GRST.