參數資料
型號: M34559G6FP
元件分類: 微控制器/微處理器
英文描述: 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP52
封裝: 10 X 10 MM, 0.65 MM PITCH, PLASTIC, LQFP-52
文件頁數: 89/93頁
文件大小: 1810K
代理商: M34559G6FP
CLRC663
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Preliminary data sheet
COMPANY PUBLIC
Rev. 3.1 — 26 September 2011
171131
95 of 126
NXP Semiconductors
CLRC663
Contactless reader IC
14. Timer unit
The external host may use this timer to manage timing relevant tasks. The timer unit may
be used in one of the following configurations:
Time-out counter
Watch-dog counter
Stop watch
Programmable one-shot
Periodical trigger
The timer unit can be used to measure the time interval between two events or to indicate
that a specific event occurred after a specific time. The timer can be triggered by events
which will be explained in the following, but the timer itself does not influence any internal
event (e.g. A time-out during data reception does not influence the reception process
automatically). Furthermore, several timer related bits are set and these bits can be used
to generate an interrupt.
The CLRC663 has 4 identical timers (Timer 0 - Timer 3). Each timer has an input clock of
13.56 MHz (derived from the 27.12 MHz quartz) and has 16 bits. The reload value for the
counter is defined in a range of 0d to 65535d in the register TnReload_Reg. Timer 4 also
can be used as wake up timer. In this case the internal LPO (Low Power Oscillator) can be
used as input clock.
The current value of the timer is indicated by the register TnCounterVal_Reg.
If the counter reaches 0 an interrupt will be generated automatically by the next clock
indicated by setting the TimerIRq bit in the register CommonIRq_Reg. If enabled, this
event can be indicated on the IRQ line. The bit TimerIRq can be set and reset by the host
controller. Depending on the configuration the timer will stop at 0h or restart with the value
from register TReload_Reg.
The status of the timer is indicated by bit TnRunning in register Tcontrol_Reg.
The timer can be manually started by setting TnRunning and TnStartStopNow in register
ControlReg or manually stopped by setting TnStartStopNow and clearing TnRunning in
register TnControl_Reg.
Furthermore the timer can be started automatically by setting the bit TnStart in the register
TnMode_Reg to fulfil dedicated protocol requirements automatically.
14.1 Usage timer unit
14.1.1 Time-Out- and Watch-Dog-Counter
Having started the timer by setting TnReloadValue the timer unit decrements the
TnCounterValue Register beginning with a certain start event. If a certain stop event
occurs e.g. a bit is received from the card, the timer unit stops (no interrupt is generated).
On the other hand, if no stop event occurs, e.g. the card does not answer in the expected
time, the timer unit decrements down to zero and generates a timer interrupt request. This
signals the
-Processor that the expected event has not occurred in the given time T
Timer.
相關PDF資料
PDF描述
M34571GD-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24
M34571G6-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24
M34571GDFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24
M34571G4FP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24
M34571G6FP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24
相關代理商/技術參數
參數描述
M34559G6-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M3455AG8FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M3455AG8-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M3455AGCFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M3455AGC-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER