參數資料
型號： M30L0T8000B0ZAQE
廠商： STMICROELECTRONICS
元件分類： PROM
英文描述： 16M X 16 FLASH 1.8V PROM, 85 ns, PBGA88
封裝： 8 X 10 MM, 0.80 MM PITCH, LEAD FREE, BGA-88
文件頁數： 48/103頁
文件大?。?/td> 794K
代理商： M30L0T8000B0ZAQE
M30L0T8000T0, M30L0T8000B0
Block locking
49/103
9.4
Lock-Down State
Blocks that are Locked-Down (state (0,1,x))are protected from program and erase
operations (as for Locked blocks) but their protection status cannot be changed using
software commands alone. A Locked or Unlocked block can be Locked-Down by issuing the
Lock-Down command. Locked-Down blocks revert to the Locked state when the device is
reset or powered-down.
The Lock-Down function is dependent on the Write Protect, WP, input pin.
When WP=0 (VIL), the blocks in the Lock-Down state (0,1,x) are protected from program,
erase and protection status changes.
When WP=1 (VIH) the Lock-Down function is disabled (1,1,x) and Locked-Down blocks can
be individually unlocked to the (1,1,0) state by issuing the software command, where they
can be erased and programmed.
When the Lock-Down function is disabled (WP=1) blocks can be locked (1,1,1) and
unlocked (1,1,0) as desired. When WP=0 blocks that were previously Locked-Down return
to the Lock-Down state (0,1,x) regardless of any changes that were made while WP=1.
Device reset or power-down resets all blocks, including those in Lock-Down, to the Locked
state.
9.5
Locking Operations During Erase Suspend
Changes to block lock status can be performed during an erase suspend by using the
standard locking command sequences to unlock, lock or lock-down a block. This is useful in
the case when another block needs to be updated while an erase operation is in progress.
To change block locking during an erase operation, first write the Erase Suspend command,
then check the Status Register until it indicates that the erase operation has been
suspended. Next write the desired Lock command sequence to a block and the lock status
will be changed. After completing any desired lock, read, or program operations, resume the
erase operation with the Erase Resume command.
If a block is locked or locked-down during an erase suspend of the same block, the locking
status bits will be changed immediately, but when the erase is resumed, the erase operation
will complete. Locking operations cannot be performed during a program suspend.
相關PDF資料
PDF描述
M31002AMLJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, LVDS OUTPUT
M31016AUMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31002AGMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31002BMMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31026AGLN1000.000000MHZ VCXO, CLOCK, 1000 MHz, LVDS OUTPUT
相關代理商/技術參數
參數描述
M30L40C 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Dual Common-Cathode Schottky Rectifier
M30L40C-E3/4W 功能描述:肖特基二極管與整流器 40 Volt 30 Amp Dual Common-Cathode RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel
M30L45C-E3/4W 功能描述:肖特基二極管與整流器 45 Volt 30 Amp Dual Common-Cathode RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel
M30LLASSM 制造商:Apex Tool Group 功能描述:Syringe; Manual Assemble Calibrated Syringe; 30 cc 制造商:Cooper Hand Tools / Weller 功能描述:CALIBRATED SYRINGE, 30CC; Dispenser Type:Syringe; Volume:30cc; Accessory Type:Calibrated Syringe
M30LLBA 制造商:Apex Tool Group 功能描述:30CC MANUAL ASSEMBLED CALIBRATED SYRINGE WITH LUER LOK™ TIP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*