參數資料
型號： M30L0T8000B0ZAQE
廠商： STMICROELECTRONICS
元件分類： PROM
英文描述： 16M X 16 FLASH 1.8V PROM, 85 ns, PBGA88
封裝： 8 X 10 MM, 0.80 MM PITCH, LEAD FREE, BGA-88
文件頁數： 33/103頁
文件大小： 794K
代理商： M30L0T8000B0ZAQE
M30L0T8000T0, M30L0T8000B0
Status Register
35/103
5.6
Program Suspend Status Bit (SR2)
The Program Suspend Status bit indicates that a program operation has been suspended in
the addressed block. The Program Suspend Status bit should only be considered valid
when the Program/Erase Controller Status bit is High (Program/Erase Controller inactive).
When the Program Suspend Status bit is High (set to ‘1’), a Program/Erase Suspend
command has been issued and the memory is waiting for a Program/Erase Resume
command.
SR2 is set within the Program Suspend Latency time of the Program/Erase Suspend
command being issued therefore the memory may still complete the operation rather than
entering the Suspend mode.
When a Program/Erase Resume command is issued the Program Suspend Status bit
returns Low.
5.7
Block Protection Status Bit (SR1)
The Block Protection Status bit is used to identify if a Program or Block Erase operation has
tried to modify the contents of a locked or locked-down block.
When the Block Protection Status bit is High (set to ‘1’), a program or erase operation has
been attempted on a locked or locked-down block.
Once set High, the Block Protection Status bit must be set Low by a Clear Status Register
command or a hardware reset before a new program or erase command is issued,
otherwise the new command will appear to fail.
5.8
Bank Write/Multiple Word Program Status Bit (SR0)
The Bank Write Status bit indicates whether the addressed bank is programming or erasing.
In Buffer Enhanced Factory Program mode the Multiple Word Program bit shows if the
device is ready to accept a new Word to be programmed to the memory array.
The Bank Write Status bit should only be considered valid when the Program/Erase
Controller Status SR7 is Low (set to ‘0’).
When both the Program/Erase Controller Status bit and the Bank Write Status bit are Low
(set to ‘0’), the addressed bank is executing a program or erase operation. When the
Program/Erase Controller Status bit is Low (set to ‘0’) and the Bank Write Status bit is High
(set to ‘1’), a program or erase operation is being executed in a bank other than the one
being addressed.
In Buffer Enhanced Factory Program mode if Multiple Word Program Status bit is Low (set to
‘0’), the device is ready for the next Word, if the Multiple Word Program Status bit is High
(set to ‘1’) the device is not ready for the next Word.
For further details on how to use the Status Register, see the Flowcharts and Pseudo codes
provided in Appendix C.
相關PDF資料
PDF描述
M31002AMLJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, LVDS OUTPUT
M31016AUMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31002AGMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31002BMMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31026AGLN1000.000000MHZ VCXO, CLOCK, 1000 MHz, LVDS OUTPUT
相關代理商/技術參數
參數描述
M30L40C 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Dual Common-Cathode Schottky Rectifier
M30L40C-E3/4W 功能描述:肖特基二極管與整流器 40 Volt 30 Amp Dual Common-Cathode RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel
M30L45C-E3/4W 功能描述:肖特基二極管與整流器 45 Volt 30 Amp Dual Common-Cathode RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel
M30LLASSM 制造商:Apex Tool Group 功能描述:Syringe; Manual Assemble Calibrated Syringe; 30 cc 制造商:Cooper Hand Tools / Weller 功能描述:CALIBRATED SYRINGE, 30CC; Dispenser Type:Syringe; Volume:30cc; Accessory Type:Calibrated Syringe
M30LLBA 制造商:Apex Tool Group 功能描述:30CC MANUAL ASSEMBLED CALIBRATED SYRINGE WITH LUER LOK™ TIP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*