參數資料
型號： M30L0T8000B0ZAQE
廠商： STMICROELECTRONICS
元件分類： PROM
英文描述： 16M X 16 FLASH 1.8V PROM, 85 ns, PBGA88
封裝： 8 X 10 MM, 0.80 MM PITCH, LEAD FREE, BGA-88
文件頁數： 20/103頁
文件大?。?/td> 794K
代理商： M30L0T8000B0ZAQE
M30L0T8000T0, M30L0T8000B0
Command interface
23/103
4.9
Buffer Enhanced Factory Program Command
The Buffer Enhanced Factory Program command has been specially developed to speed up
programming in manufacturing environments where the programming time is critical.
It is used to program one or more Write Buffer(s) of 32 Words to a block. Once the device
enters Buffer Enhanced Factory Program mode, the Write Buffer can be reloaded any
number of times as long as the address remains within the same block. Only one block can
be programmed at a time.
The use of the Buffer Enhanced Factory Program command requires certain operating
conditions:
●
VPP must be set to VPPH
●
VDD must be within operating range
●
Ambient temperature TA must be 30°C ± 10°C
●
The targeted block must be unlocked
●
The start address must be aligned with the start of a 32 Word buffer boundary
●
The address must remain the Start Address throughout programming.
Dual operations are not supported during the Buffer Enhanced Factory Program operation
and the command cannot be suspended.
If the block is protected, then the Buffered Enhanced Factory Program operation will abort.
The data in the block will not be changed as a result and the Status Register will output the
error.
The Buffer Enhanced Factory Program Command consists of three phases: the Setup
Phase, the Program and Verify Phase, and the Exit Phase, Please refer to Table 6: Factory
Program Command for detail information.
4.10
Setup Phase
The Buffer Enhanced Factory Program command requires two Bus Write cycles to initiate
the command.
●
The first Bus Write cycle sets up the Buffer Enhanced Factory Program command.
●
The second Bus Write cycle confirms the command.
After the confirm command is issued, read operations output the contents of the Status
Register. The read Status Register command must not be issued as it will be interpreted as
data to program.
The Status Register P/E.C. Bit SR7 should be read to check that the P/E.C. is ready to
proceed to the next phase.
If an error is detected, SR4 goes high (set to ‘1’) and the Buffer Enhanced Factory Program
operation is terminated. See Status Register section for details on the error.
相關PDF資料
PDF描述
M31002AMLJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, LVDS OUTPUT
M31016AUMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31002AGMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31002BMMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31026AGLN1000.000000MHZ VCXO, CLOCK, 1000 MHz, LVDS OUTPUT
相關代理商/技術參數
參數描述
M30L40C 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Dual Common-Cathode Schottky Rectifier
M30L40C-E3/4W 功能描述:肖特基二極管與整流器 40 Volt 30 Amp Dual Common-Cathode RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel
M30L45C-E3/4W 功能描述:肖特基二極管與整流器 45 Volt 30 Amp Dual Common-Cathode RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel
M30LLASSM 制造商:Apex Tool Group 功能描述:Syringe; Manual Assemble Calibrated Syringe; 30 cc 制造商:Cooper Hand Tools / Weller 功能描述:CALIBRATED SYRINGE, 30CC; Dispenser Type:Syringe; Volume:30cc; Accessory Type:Calibrated Syringe
M30LLBA 制造商:Apex Tool Group 功能描述:30CC MANUAL ASSEMBLED CALIBRATED SYRINGE WITH LUER LOK™ TIP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*