參數資料
型號： M30L0T8000B0ZAQE
廠商： STMICROELECTRONICS
元件分類： PROM
英文描述： 16M X 16 FLASH 1.8V PROM, 85 ns, PBGA88
封裝： 8 X 10 MM, 0.80 MM PITCH, LEAD FREE, BGA-88
文件頁數： 22/103頁
文件大?。?/td> 794K
代理商： M30L0T8000B0ZAQE
M30L0T8000T0, M30L0T8000B0
Command interface
25/103
4.13
Program/Erase Suspend Command
The Program/Erase Suspend command is used to pause a Program or Block Erase
operation. The command can be addressed to any bank.
The Program/Erase Resume command is required to restart the suspended operation.
One bus write cycle is required to issue the Program/Erase Suspend command. Once the
Program/Erase Controller has paused bits SR7, SR6 and/ or SR2 of the Status Register will
be set to ‘1’.
The following commands are accepted during Program/Erase Suspend:
●
Program/Erase Resume
●
Read Array (data from erase-suspended block or program-suspended Word is not
valid)
●
Read Status Register
●
Read Electronic Signature
●
Read CFI Query.
Additionally, if the suspended operation was a Block Erase then the following commands are
also accepted:
●
Clear Status Register
●
Program (except in erase-suspended block)
●
Buffer Program (except in erase suspended blocks)
●
Block Lock
●
Block Lock-Down
●
Block Unlock.
During an erase suspend the block being erased can be protected by issuing the Block Lock
or Block Lock-Down commands. When the Program/Erase Resume command is issued the
operation will complete.
It is possible to accumulate multiple suspend operations. For example: suspend an erase
operation, start a program operation, suspend the program operation, then read the array.
If a Program command is issued during a Block Erase Suspend, the erase operation cannot
be resumed until the program operation has completed.
The Program/Erase Suspend command does not change the read mode of the banks. If the
suspended bank was in Read Status Register, Read Electronic signature or Read CFI
Query mode the bank remains in that mode and outputs the corresponding data.
Refer to Dual Operations section for detailed information about simultaneous operations
allowed during Program/Erase Suspend.
During a Program/Erase Suspend, the device can be placed in standby mode by taking Chip
Enable to VIH. Program/erase is aborted if Reset, RP, goes to VIL.
the Program/Erase Suspend command.
相關PDF資料
PDF描述
M31002AMLJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, LVDS OUTPUT
M31016AUMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31002AGMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31002BMMJ1000.000000MHZ VCXO, CLOCK, 1000 MHz, CMOS OUTPUT
M31026AGLN1000.000000MHZ VCXO, CLOCK, 1000 MHz, LVDS OUTPUT
相關代理商/技術參數
參數描述
M30L40C 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Dual Common-Cathode Schottky Rectifier
M30L40C-E3/4W 功能描述:肖特基二極管與整流器 40 Volt 30 Amp Dual Common-Cathode RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel
M30L45C-E3/4W 功能描述:肖特基二極管與整流器 45 Volt 30 Amp Dual Common-Cathode RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel
M30LLASSM 制造商:Apex Tool Group 功能描述:Syringe; Manual Assemble Calibrated Syringe; 30 cc 制造商:Cooper Hand Tools / Weller 功能描述:CALIBRATED SYRINGE, 30CC; Dispenser Type:Syringe; Volume:30cc; Accessory Type:Calibrated Syringe
M30LLBA 制造商:Apex Tool Group 功能描述:30CC MANUAL ASSEMBLED CALIBRATED SYRINGE WITH LUER LOK™ TIP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*