Under
development
Preliminary Specifications REV.B3
Specifications in this manual are tentative and subject to change.
Mitsubishi Microcomputers
M32C/83 group
SINGLE-CHIP 16/32-BIT CMOS MICROCOMPUTER
Clock synchronous serial I/O mode
178
Pin name
Function
Method of selection
TxDi
(P63, P67, P70,
P92, P96)
Serial data output
(Note 1)
Serial data input
(Note 2)
Transfer clock output
(Note 1)
Transfer clock input
(Note 2)
Programmable I/O port
(Note 2)
(Outputs dummy data when performing reception only)
RxDi
(P62, P66, P71,
P91, P97)
CLKi
(P61, P65, P72,
P90, P95)
Internal/external clock select bit (bit 3 at addresses 036816, 02E816,
033816, 032816, 02F816) = “0”
Internal/external clock select bit (bit 3 at addresses 036816, 02E816,
033816, 032816, 02F816) = “1”
Port P61, P65, P72, P90 and P95 direction register (bits 1 and 5 at address
03C216, bit 2 at address 03C316, bit 0 and 5 at address 03C716) = “0”
Port P62, P66, P71, P91 and P97 direction register (bits 2 and 6 at address
03C216, bit 1 at address 03C316, bit 1 and 7 at address 03C716)= “0”
(Can be used as an input port when performing transmission only)
CTS/RTS disable bit (bit 4 at addresses 036C16, 02EC16, 033C16, 032C16,
02FC16) =“0”
CTS/RTS function select bit (bit 2 at addresses 036C16, 02EC16, 033C16,
032C16, 02FC16) = “0”
Port P60, P64, P73, P93 and P94 direction register (bits 0 and 4 at address
03C216, bit 3 at address 03C316, bits 3 and 4 at address 03C716) = “0”
CTS/RTS disable bit (bit 4 at addresses 036C16, 02EC16, 033C16,
032C16, 02FC16) = “0”
CTS/RTS function select bit (bit 2 at addresses 036C16, 02EC16, 033C16,
032C16, 02FC16) = “1”
CTS/RTS disable bit (bit 4 at addresses 036C16, 02EC16, 033C16,
032C16, 02FC16) = “1”
CTS input
(Note 2)
RTS output (Note 1)
CTSi/RTSi
(P60, P64, P73,
P93, P94)
Item
Specification
Error detection
Overrun error (Note)
This error occurs when the next data is started to receive and 6.5 transfer clock is
elapsed before UARTi receive buffer register are read out.
Select function
CLK polarity selection
Whether transmit data is output/input at the rising edge or falling edge of the transfer
clock can be selected
LSB first/MSB first selection
Whether transmission/reception begins with bit 0 or bit 7 can be selected
Continuous receive mode selection
Reception is enabled simultaneously by a read from the receive buffer register
Reversing serial data logic
Whether to reverse data in writing to the transmission buffer register or reading the
reception buffer register can be selected.
TxD, RxD I/O polarity reverse
This function is reversing TxD port output and RxD port input. All I/O data level is
reversed.
Note : If an overrun error occurs, the UARTi receive buffer will have the next data written in.
Table 1.18.3 lists the functions of the input/output pins during clock synchronous serial I/O mode. Note
that for a period from when the UARTi operation mode is selected to when transfer starts, the TxDi pin
outputs a “H”. (If the N-channel open drain is selected, this pin is in floating state.)
Table 1.18.3. Input/output pin functions in clock synchronous serial I/O mode
________
Note 1: Select TxD output, CLK output and RTS output by the corresponding function select registers A, B and C.
Note 2: Select I/O port by the corresponding function select register A.
Table 1.18.2. Specifications of clock synchronous serial I/O mode (2/2)